Manuals / Brands / Computer Equipment / Computer Monitor / Eizo / Computer Equipment / Computer Monitor

Eizo CG245W 3-3. Setting the EIZO Logo Display [Logo], 3-4. Setting Orientation [Orientation]

1 66

Download 66 pages, 6.19 Mb

28 Chapter 3 Setting Monitor

3-3. Setting the EIZO Logo Display [Logo]

The EIZO logo appears on the display when turni ng on the monitor. This function allows you to display,

or not, the EIZO logo.

Procedure

1. Press to turn off the monitor.

2. Press holding down at least 2 seconds to turn on the monitor.

The Optional Settings menu appea rs.

3. Choose <Logo> from the <O ptional Settings> menu, and press .

4. Select “On” or “Off ” with or , and press .

5. Select “Finish” with or .

6. Press to exit the O ptional Settings.

The Optional Settings menu is closed.

3-4. Setting Orientation [Orientation]

This function allows you to change the orientation of the Adjustment menu when usi ng the monitor screen

in vertical display position. (Default settings : Land scape)

Procedure

1. Choose <Menu Setting s> from the Adjustment menu, and press .

2. Choose <Orient ation> from the <Menu Settings> menu, and press .

3. Select “Landscape” or “ Portrait” with or .

4. Press to exit the adjus tment.

5. When selecti ng “Portrait”, turn the monitor screen 90 ° in clockwise direction.

Attention

• Be sure th at the cables are correctly conne cted.

Tips

• For using the monitor w ith “Portrait” position, the g raphics board supporti ng portrait display is requi red. When

placing the monitor in a “Portrait ” position, settings of your graphics b oard need to be changed. Refer to the

manual of the graphics board for detail s.

Contents

Main [Location of Caution Statement] Notice for this monitor Cleaning To use the monitor comfortably Page CONTENTS 6 Chapter 1 Introduction 1-1. Features CAUTION Be careful of the following points when using the monitor hood. 1-2. Controls and Functions 1-3. Utility Disk 10 1- 4. Basic Operation and Functions Basic operation of menu 1 2 3 12 Functions Page 14 Chapter 2 Adjusting Screen 2-1. Setting Screen Resolution Compatible Resolutions/Frequencies Digital Input (DVI/DisplayPort) Resolution Display Mode Frequency Dot Clock Setting Resolution Page Page Page Page Page 2-5. Displaying Lower Resolutions 2-6. Conguring moving image performance [Overdrive] Chapter 3 Setting Monitor 3-1. Enabling/Disabling Mode Selection [Mode Preset] 3-2. Locking Buttons [Key Lock] 28 3-3. Setting the EIZO Logo Display [Logo] 3-4. Setting Orientation [Orientation] 3-5. Setting Language [Language] Selectable languages 3-6. Setting Range of Frequency [Signal Bandwidth] Page 3-9. Restoring the Default Setting 32 Chapter 4 SelfCalibration 4-1. Executing SelfCalibration [Calibration] 4-2. Checking Calibration Results [Result] 4-3. Setting Calibration Details [Setting] 34 Set the calibration schedule for SelfCalibration. 4. Adjust using or . 5. Press to exit the adjustment. The calibration schedule is set. 36 Chapter 5 Power Saving Function 5-1. Setting the Power Saving [Power Save] Chapter 6 Troubleshooting 38 Page Chapter 7 Reference 7-1. Attaching an Arm Use the screws that hold the monitor and stand together for installation. [Attachment Procedure] 1 Page 7-3. Making Use of USB (Universal Serial Bus) 7-4. Displaying Monitor Information 7-5. Specications Main default settings (factory settings) Chapter 7 Reference Outside Dimensions Unit: mm (inch) 172 Connector Pin Assignment DVI-I con nector D isplayPort connector USB por t 7-6. Glossary Page Page 7-7. Preset Timing About TCO 03 FCC Declaration of Conformity For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity Canadian Notice HinweiseHinweise zur Auswahl des richtigen Schwenkarms fr Ihren Monitor 56 LIMITED WARRANTY LIMITED WARRANTY BEGRENZTE GARANTIE 58 GARANTIE LIMITE GARANTA LIMITADA 60 GARANZIA LIMITATA BEGRNSAD GARANTI 62 64