BP7306 Nottingham 6/19/06 1:00 PM Page 14
6. Screw wall control into wall box and 
install decorator style faceplate (included). Leave wall control in “OFF” mode until fan installation is completed.
7. Refer to page 5 and complete the ceiling fan installation.
BLK | T |
|
|
| HOT |
|
|
| |
HI | O |
|
|
|
|
|
|
| |
|
| 1 | 2 | 0V |
|
| O |
| E |
MED |
|
| AC | S | C | ||||
|
|
|
| UR |
| ||||
LIGHT |
|
|
|
|
|
|
|
| |
| T |
| O |
LOW | LOAD |
FAN OFF |
|
5.Connect one black wire of the wall control to both remaining traveler wires in the wall box and secure with wire connector supplied.
NOTE: Retrofit
EMERSON | ® | |
| ||
OFF | ON |
|
Figure 19
BLACK
FAN/LIGHT WALL CONTROL
G
R
D N U O
| HOT |
| FAN/LIGHT |
|
|
|
| WALL |
|
WALL |
| EMERSON | CONTROL | EMERSON |
|
|
|
| |
BOX | BLACK |
| BLK | BLK |
|
| |||
|
|
| ||
|
|
| TRAVELER |
|
| NEUTRAL |
| WIRE |
|
LOAD
BLACK
GROUND
|
|
|
|
| REMOTE CONTROL |
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
| RECEIVER LOCATED |
|
|
|
|
| ||
(On fan controlled by two different wall | WITHIN THE CEILING |
|
|
|
| ||||||||||||
controls) (See Figures 20 and 21.) |
|
| COVER |
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| |||||||||
1. Disconnect power at circuit breaker or | Figure 20 |
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
| |||||||||||
remove fuse. |
|
|
|
|
|
|
| 6. Place wall control into wall box. Screw | |||||||||
2. At all | wall | box | locations | remove | |||||||||||||
in place | and | install decorator style | |||||||||||||||
faceplates | and screws | from | existing | ||||||||||||||
faceplate (included). |
|
| |||||||||||||||
controls. Pull | controls | out from | wall |
|
| ||||||||||||
7. Next, install the other wall control into | |||||||||||||||||
boxes and determine which wall box | |||||||||||||||||
the wall box containing the load wire. | |||||||||||||||||
contains the “hot” lead and which wall | |||||||||||||||||
Connect | the | black wire of the | wall | ||||||||||||||
box contains | the | “load” | wire. Also, | ||||||||||||||
control to | the | traveler wire(s) | already | ||||||||||||||
identify | traveler | wires | which | are | |||||||||||||
connected | to | the | black wire | (in | the | ||||||||||||
common | to | both | wall | boxes. | |||||||||||||
other wall | box). | Secure with | wire | ||||||||||||||
Disconnect wires from existing controls | |||||||||||||||||
connectors supplied. |
|
| |||||||||||||||
only. Do not attempt to disconnect any |
|
| |||||||||||||||
8. Connect one black wire of the wall | |||||||||||||||||
wires not already connected to existing | |||||||||||||||||
controls. |
|
|
|
|
|
|
|
| control to the “load” (black) wire and | ||||||||
3. Before installing wall control, place wall | secure with wire connector supplied. | ||||||||||||||||
9. Place the second wall control into the | |||||||||||||||||
control in “OFF” mode by pushing | |||||||||||||||||
“ON/OFF” switch to the “OFF” position. | wall box. Screw in place and install | ||||||||||||||||
|
|
|
|
|
|
|
|
|
| decorator style faceplate (included). | |||||||
| ! | WARNING |
|
|
| Leave switch in “OFF” mode until fan | |||||||||||
|
|
|
|
|
|
|
|
|
| installation is completed. |
|
| |||||
Do not connect any neutral (white) |
|
|
| ||||||||||||||
| 10. Refer to page 5 and complete the | ||||||||||||||||
wire to this control. Incorrect wiring |
| ||||||||||||||||
will damage this control. |
|
|
|
| ceiling fan installation. |
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
4. Install a wall control in the wall box containing the “hot” wire first. Connect the black wire of the wall control to the “hot” wire. Securely connect wires with wire connectors supplied.
14
