XSR Getting Started Guide A-17 | Enterasys Networks XSR-3150

Cable, CompactFlash and Accessory Specifications

Installing Shunt/Terminal Strip

To install the shunt or terminal strip, attach two dual-pin units vertically to P1 and P2 four-pin jumpers corresponding to the RJ-45 port using a balun, as shown in Figure A-20. Any other RJ-45 ports on the NIM card connected to 120-ohm lines do not require shunts.

Figure A-20 Installing a Termination Shunt on BRI-S/T NIM Card

Receive Pair Term ination

F16 F17

T1

P1

Port 0

F1

F2J1

F3

F4

F14 F15			T2
	P2
				Transmit Pair Termination
F5	F6 J2	F7	F8	Port 1

R132	R133
CR1	CR2
Port 0	Port 1

XSR Getting Started Guide A-17

Image 103

Enterasys Networks XSR-3150 manual XSR Getting Started Guide A-17

Contents

Version PeditionSecurity RouterPage Enterasys Networks, Inc Minuteman Road Andover, MA Regulatory Compliance Information Industry Canada Notices Product Safety Supplement to Product Instructions Vcci Notice N826 Enterasys Networks, Inc. Firmware License Agreement Page Page Contents BRI Leased Line BRI Leased Frame Relay BRI Switched Line Index Appendix a Specifications Xiv About This Guide Contents of the Guide Bold/En negrilla FTP Getting Help Xviii System Description Overview Typical XSR-3150 Topology Hardware Features XSR-3150 IP Protocol Software FeaturesOperating System Industry-common CLI Snmp and Statistics Gathering IP Routing Frame Relay Security Integrated Services Digital Network Isdn BRI/PRI Dynamic Host Configuration Protocol Dhcp Virtual Private Network VPN Quality of Service QoS GRE over IPSec Dial-on-Demand/Bandwidth-on-Demand DoD/BoD Dial ServiceDial Backup Asynchronous Digital Subscriber Line Adsl Unpack the XSR from the shipping box. Remove accessories Installation Overview Installation Overview Introduction Installation Site SuggestionsVerifying Your Shipment Removing XSR Cover Installing NIM Cards and Rack Mounting XSR Fastening Rack Brackets CompactFlash Card Installation Installing a CompactFlash Memory Card Formatting the CompactFlash Card CompactFlash Card for the Adsl NIM 3150 Connecting Cables 11 Connecting High Speed Serial Connector 13 Connecting Adsl Connector 15 Attaching GigabitEthernet Connector 17 Attaching Ethernet LAN NIM Connector 19 Connecting Dual Internal Power Supply Cords Initializing XSR Software Software Configuration Initializing XSR Software Configuring RAI for Frame Relay Optional Configuring Remote Auto InstallOpening a COM Console Session Remote Auto Install Attempting Forever Configuring RAI over Adsl Configuring RAI for Dhcp over LAN Pppoe limit max-sessions Setting the Clock Configuring the XSR Name and User InformationSetting User Name, Privilege and Password Configuring the WAN Ports Configuring the LAN PortsPRI Configuration BRI Leased Line BRI Configuration BRI Leased Frame Relay BRI Switched Line PPPoE Adsl ConfigurationPPPoA IPoA Firewall Sample Configuration XSR Complete LAN and WAN interface configuration Setting Up RIP Routing Configuring Frame Relay Point to Point Networks Configure Ospf Routing Setting Up an Snmp Community String, Traps and V3 Values Configuring Message Logging and Severity Level Connecting Remotely via the Web Viewing Your Configuration Web Product Version Window Pstn LAN-PPP Services Sample Configuration XSRconfig-controllerT1-1/0#no shutdown Configure Quality of Service Frame Relay WAN Link with PPP Backup Sample ConfigurationConfigure Users and Passwords Configure LAN Interface XSRconfig-pmap-cpriority-policy#priority high 30 Configure WAN/Frame Relay Port Apply QoS XSRconfig#interface serial 1/0.2 multipoint Configure the Dial Backup Connection Configure Ospf RoutingConfigure More Access Lists Configure DHCP/BOOTP Relay Configure Snmp Configure Access Control Lists VPN Site-to-Site Sample ConfigurationGenerate Master Encryption Key Create a Transform Set Set Up IKE Phase I SecurityConfigure IKE Policy for Remote Peer Configure Crypto Maps Configuring VPN at Interface Mode and Setting Up RIP Configuring Authentication AAA VPN Sample Configuration with Network Extension Mode Enable Network Address Translation Create the Isakmp IKE global peer Initialization Output XSR Rebooting Characteristics Power-Up Reboot Reboot Triggers Power-up Error Conditions Bootrom Monitor Mode Commands XSR-3150 bu btXSR300012.fls Verifying btXSR300012.fls file Copy Dir Del Ffc Rename Remove FTP Bootrom Monitor Mode Commands System Specifications Specifications WAN Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-3 COM COM Console Port Mini-GBIC Fiber, Copper Port GigabitEthernet Ports Copper/Fiber-optic Ethernet NIMs Regulatory/Safety Compliance 21 DTE Port Serial NIM Card Port Figure A-8 EIA-232/530 DTE Pin Assignments Figure A-9 EIA-449 DTE Pin Assignments Figure A-10 Combined V.35/EIA-232/530 DTE Pin Assignments Figure A-11 DTE Pin Assignments T1/E1/ISDN PRI T1/E1/ISDN PRI NIM Card Ports Figure A-14 Balun for E1 or PRI Connection Balun for E1 or PRI NIM Cards Grounding Shunt for E1 NIM Cards Installing Shunt/Terminal Strip Figure A-17 1-Port T3/E3 NIM Card T3/E3 NIM Card Termination Shunt for the Isdn BRI-S/T NIM Card Port BRI-S/T Isdb NIM Card Ports XSR Getting Started Guide A-17 Figure A-21 Isdn BRI-U NIM Card RJ-49C ports shown Port BRI-U NIM Card Ports Figure A-23 Adsl NIM Card Port Adsl NIM Card Port Figure A-25 T1/E1 D&I NIM Card T1/E1 Drop & Insert D&I NIM LED Behavior CompactFlash Memory Card TX LED Index Index-2