Problem Solving
Have the "Sync. " and | The projector has an automatic adjustment function that causes the | ||||
"Tracking " settings been | optimum images to be projected. However, for some types of signal, | ||||
adjusted correctly? | the correct adjustments may not be obtained even after automatic | ||||
|
|
|
|
| adjustment is carried out. In such cases, use the "Tracking" and |
|
| Computer and RGB |
|
| |
|
|
|
| "Sync." menu commands to make the adjustments. | |
|
| video signals only |
|
| |
|
|
|
| s "Image" - "Picture Quality" - "Tracking", "Sync." page 26 | |
|
|
|
|
| |
|
|
|
|
|
|
Has the correct resolution | Set the computer so that the signals that are output are compatible | ||||
been selected? | with this projector. | ||||
|
|
| s "List of Supported Monitor Displays" page 45, Computer | ||
|
| Only when projecting |
| ||
|
| computer images |
| documentation | |
|
|
|
|
|
|
Image is truncated (large) or small
Has the correct aspect been | Press | to select the aspect that corresponds to the input signal. | ||
selected? | s p.18 |
| ||
|
|
| If images with subtitles are being projected using "Zoom", use the | |
|
|
| "Zoom Caption" menu command to adjust the images. s page 28 | |
|
|
|
| |
Has the "Position" setting | Use the "Position" menu command to make the adjustment. | |||
been adjusted correctly? | s"Setting" - "Screen" - "Position" page 27 | |||
|
|
|
| |
Has the computer been set for | If dual display has been activated in the Display Properties of the | |||
dual display? | computer's Control Panel, the projector will only project about half | |||
|
|
| of the image on the computer screen. To display the whole of the | |
| Only when projecting |
| ||
|
| image on the computer screen, turn off the dual display setting. | ||
| computer images |
| ||
|
| s Computer video driver documentation | ||
|
|
| ||
|
|
|
| |
Has the correct resolution | Set the computer so that the signals that are output are compatible | |||
been selected? | with this projector. | |||
|
|
| ||
|
| s "List of Supported Monitor Displays" page 45, Computer | ||
| Only when projecting |
| ||
| computer images |
| documentation | |
|
|
|
|
|
Image colours are not right
Are the image signal format | If a composite video g or | |
settings correct? | If projection does not occur when the "Video Signal" menu | |
| command is set to "Auto", select the signal format that matches the | |
| signal source. |
|
| s "Setting" - "Input Signal" - "Video Signal" page 30 | |
|
| |
| If the signal source is connected to the [InputA] port | |
| Use the "Input Signal" menu command to set the signal format that | |
| matches the signal that is being projected from the connected | |
| equipment. |
|
| s "Setting" - "Input Signal" - "Input A" page 30 | |
| You can also press | on the remote control to select the format. |
| s page 15 |
|
|
| |
Are the cables connected | Check that all of the cables required for projection are securely | |
correctly? | connected. s page 12 |
|
|
| |
Has the image contrast | Use the "Contrast" menu command to adjust the contrast. | |
been adjusted correctly? | s "Image" - "Picture Quality" - "Contrast" page 26 | |
|
| |
Has the colour been adjusted | Use the "Color Temp." and "Skin Tone" menu command to adjust the | |
correctly? | colour. |
|
| s "Image" - "Picture Quality"- "Color Temp.", "Skin Tone" | |
| page 26 |
|
|
|
|
Troubleshooting
37