Signal |
| Return |
|
|
|
|
|
|
Pin |
| Pin | Signal | oniectDri | Description | |||
|
|
|
|
|
|
|
|
|
13 | - | SLCT | OUT | Pulled up to +5 volts through 3.3 Kohm | ||||
|
|
|
|
|
|
|
| resistance. |
|
|
|
|
|
|
|
|
|
14 | - |
|
|
|
|
|
| |
A u t o | IN | When this signal is LOW, the paper is | ||||||
| - | FEED |
|
|
| automatically fed 1 line after printing. | ||
| - | - |
|
|
|
| (The signal level can be fixed to this by | |
| XT |
|
|
| ||||
|
|
|
|
|
|
|
| setting DIP switch |
15 |
|
|
| - |
|
|
| |
|
| NC |
|
| Not used. | |||
|
|
|
| - |
|
|
| |
16 |
|
| GND |
|
| Logic ground level. | ||
|
| - |
| - |
|
|
| |
17 |
| CHASSIS |
|
| Printer’s chassis ground, which is | |||
| - | GND | - |
|
| isolated from the logic ground. | ||
18 | - | NC | - |
|
|
| ||
|
| Not used. | ||||||
|
|
| - |
|
|
| ||
- | GND |
|
| |||||
|
|
|
|
|
| |||
31 | 16 | INIT | IN | When this level becomes LOW, the | ||||
|
|
|
|
|
|
|
| printer controller is reset to its |
|
|
|
|
|
|
|
| state and the print buffer is cleared. This |
|
|
|
|
|
|
|
| level is normally HIGH; its pulse width |
|
|
|
|
|
|
|
| must be more than 50 microseconds at |
|
|
|
|
|
|
|
| the receiving terminal. |
|
|
|
|
|
| |||
32 | - |
|
|
|
| |||
ERROR | OUT | This level becomes LOW when the | ||||||
|
|
|
|
|
|
|
| printer is: |
|
|
|
|
|
|
|
| 1) in paper out state. |
|
|
|
|
|
|
|
| 2) off line. |
|
|
|
|
|
|
|
| 3) in error state. |
| - |
| - |
|
|
| ||
33 | GND |
|
| Same as for Pins 1 | ||||
| - | NC | - |
|
|
| ||
34 |
|
| Not used. | |||||
| - | - |
|
|
|
| ||
35 |
| OUT | Pulled up to 5V through 3.3 Kohm | |||||
|
|
|
|
|
|
|
| resistance. |
| - |
|
|
|
|
| ||
36 |
| IN |
| |||||
SLCT IN | The DC1/DC3 code is valid only when | |||||||
|
|
|
|
|
|
|
| this signal is HIGH. (Internal fixing can |
|
|
|
|
|
|
|
| be carried out with Jumper J10. The |
|
|
|
|
|
|
|
| level of this signal is |
|
|
|
|
|
|
|
| LOW.) |
|
|
|
|
|
|
|
|
|