![](/images/new-backgrounds/1100174/10017423x1.webp)
INSTALLATION |
Daisy Chain Cable to Power Sensors for Transmitter Channels 11 - 20 Antenna Power Sensor Cable to Power Sensors for Antennas 1 & 2 Daisy Chain Cable to Power Sensors for Transmitter Channels 1 - 12
19C852632G1 POWER SENSOR INTERFACE MODULE
|
| 188D6466P2 Cables (5 Each) |
|
| |
|
| J3 |
|
|
|
|
| J4 |
|
|
|
J1 | J2 | J5 |
|
|
|
|
| J6 |
|
|
|
|
| J7 |
|
|
|
J9 | J8 |
|
|
| |
188D6466P1 Cable |
|
|
| ||
| VDT Interfaces |
|
|
| |
|
| PORT 8 | PORT 7 | PORT 6 | PORT 5 |
|
| PORT 4 | PORT 3 | PORT 2 | PORT 1 |
POWER MONITOR UNIT
Programming |
|
|
|
| #18 Red | #18 Black | |
Terminal |
|
|
|
|
| ||
Connection |
|
|
|
|
|
|
|
DOWNLINK GETC |
| 1 |
| 7 | 12 |
| |
|
|
|
| ||||
(TRUNKING CARD) |
|
| 6 |
|
|
| |
|
|
|
|
|
|
| |
|
|
|
| Use 19D903880P100 Cable If |
| ||
|
|
|
| Connecting to DILOG Panel |
| ||
A 0 | 5 | 11 | B | 0 | 5 |
| 11 |
|
|
|
|
|
|
| 13B |
DILOG |
|
|
| DILOG |
|
|
|
|
|
| Use 19D903880P101 Cable If |
| |||
|
|
| Connecting to Site Controller Computer |
Port 29
SITE CONTROLLER
COMPUTER
Figure 10 - Connections for Addition from No PMU
B. Upgrade from Old PMU
Use this procedure only if your Site Controller cabinet has EDACS Interface panels and an old PMU.
This procedure consists of upgrading the Site Controller by replacing the old PMU, replacing the old Power Sensor interface module, and replacing the cables between them.
Parts Required
Before you start this procedure, be sure you have all the parts on hand. The parts for this procedure are shown in Table 3.
Table 3 - Parts for Upgrade from Old PMU
QTY | PART # | DESCRIPTION |
1350A1380P1 Decibel Products DB8860- based PMU Unit
1 | 188D6466P1 | Cable - PMU to Power |
|
| Sensor interface module |
|
|
|
5 | 188D6466P2 | Cable - PMU to Power |
|
| Sensor interface module |
119C852632G1 Power Sensor interface module
Procedure
The following steps involve equipment in the Site Controller cabinet only:
1.Turn off the main 12V power supply for the cabinet.
2.Mark “+” on the wire going to the screw terminal marked “+” on the back of the old PMU. Then disconnect this wire at the PMU end.
3.Mark
4.Mark
5.Disconnect any cables going to the connectors marked “Antennas
6.Replace the old PMU with the new PMU. There will be a half rack unit space (7/8 inch) both above and below the new PMU.
7.Connect the existing wire labeled “+” in step 2 to the terminal labeled “+” on the back of the new PMU.
8.Connect the existing wire labeled
9.Connect the existing cable labeled “RS232” in step 4 to the
10.Find the Power Sensor interface module mounted in the left end of the upper EDACS Interface Panel in the upper rear of the cabinet. If a cable is connected to the
12