Configuration, RS-232 connection | Extron electronic ISM 182

Installation, cont’d

RS-232 connection

7Remote port — Connect a host device, such as a computer or touch panel control, to the Integration Seamless Matrix switcher via this 9-pin D connector for serial RS-232 control (figure 2-9).

	Pin	RS-232	Function	5	1
	1	—	Not used

	2	TX	Transmit data
	3	RX	Receive data	9	6
	4	—	Not used
				Female
	5	Gnd	Signal ground	1	5
	6	—	Not used

	7	—	Not used
	8	—	Not used	6	9
	9	—	Not used
				Male

Figure 2-9 — Remote port pin assignments

See chapter 4, Programmer’s Guide, for definitions of the SIS commands and chapter 5, Switcher Software to install and use the control software.

Configuration

The ISM can be configured using either the front panel controls, the SIS, or the Windows Control program. See chapter 3, Operation, chapter 4, Programmer’s Guide, and chapter 5, Switcher Software.

2-8 Integration Scaling Matrix Switcher • Installation

Image 22

Extron electronic ISM 182 manual Configuration, RS-232 connection

Contents

Integration Scaling Matrix Switchers ISM 482 & ISM Sicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad Español Quick Start Integration Scaling Matrix Switcher QS-1 Quick Start Integration Scaling Matrix Switcher, cont’d QS-2 Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Introductiontroduction, cont’d About the SwitcherIntegration Scaling Matrix Switcher Introduction About this Manual Extron ISM Features Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Tabletop placement Installationstallation, cont’dMounting the Switcher Integration Scaling Matrix Switcher Installation Cabling and Rear Panel Views Input connections Installation, cont’d Captive screw connector wiring for inputs Output connections BNC output connections for Rgbhv and Rgbs video Ethernet connection Cabling and RJ-45 connector wiringChoosing a network cable Wiring the network cable RJ-45 connector pinout tables Configuration RS-232 connection Three Operationeration, cont’d Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Video/Audio selection button and LEDs Input buttons, LEDs, and label window Outputs buttons and LEDsFront panel input label window Operation, cont’d Picture adjustment buttonsBlack/Mute button and LEDs LCD display Adjustment knobsMenu control buttons Power Front Panel Operations Menu system overview Extron Electronics ISM 60-425-01 Version Video & Audio Configuration menu Input Configuration submenu Output Configuration menu Output Resolution submenu Resolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Type and Polarity submenu Advanced Configuration menu Video & Audio Test Pattern submenu Blue Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenu PAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenu User Presets menu Save Preset submenu Erase Preset submenu Exit menu Picture adjustments 13 Picture adjustments flowchart Front panel security lockout executive mode 14 Front panel security lockout flowchart Optimizing the Video IP information Setting up a DVD source Controls to position the image Optimizing the Audio TroubleshootingGeneral checks Specific problems Problem Cause Operation, cont’d Four RS-232 Link Integration Scaling Matrix Switcher Programmer’s GuideEthernet Link Symbols Default address Ties creation Switcher-Initiated MessagesPower-up Input and output video type X2 Col Programmer’s Guide, cont’d Switcher error responses Host-to-Switcher InstructionsUsing the command/response table Command Ascii Command Response Additional description Horizontal size BrightnessContrast Vertical size Horizontal detail filter RGB and component video inputs Pixel phaseBottom blanking Vertical detail filter RGB and component video inputs Freeze User presetsAuto Memories Test pattern Verbose mode Executive modeInformation requests Command/response table for IP SIS commands Resets Delay times Command/response table for special function SIS commandsScaler settings Blue screen Enhanced modePAL film mode Edge smoothing Memory backup Command Hex Command ResponseAdditional description Five Integration Scaling Matrix Switcher Switcher Software Installing the softwareEthernet protocol settings Control Software for Windows Using the control program If you selected a comm port, proceed to step Switcher Software, cont’d Windows Control program window Using the help program Button-Label Generator Installing the software Using the software Six EthernetOperation,cont’d Integration Scaling Matrix Switcher Ethernet OperationLoad the Startup Control Control Control Change the RGB delayEthernet Operation, cont’d Create a tie Output a test pattern Executive modeFreeze the output Preview the scan rate System Configuration System Configuration ISM IP Address field Administration fieldsISM IP Settings fields ISM Name field File Management File Management Input configuration I/O Configuration Output resolution, rate, sync format, and polarity Output resolution Output rate Output format Output polarity AAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet Connection, cont’d Ping to determine the switcher’s IP address Ping to determine the Web IP address Telnet tips Connect as a Telnet clientOpen Set carriage return-line feed Escape character and Esc keyLocal echo Close Ethernet Connection, cont’d AppendixBB Specifications Integration Scaling Matrix Switcher Reference Information Audio Reference Information, cont’d Optional accessoriesCables and connectors Part Numbers BNC-5 Mini HR Cable Assorted connectors BNC connectorsBNC-4 Mini HR Cable Plenum BNC-5 Mini HR Cable Firmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA