Manuals / Fisher & Paykel / Kitchen Appliance / Dishwasher

Fisher & Paykel DD60ST 7 16b DETERMINE BADGE CUTOUT LOCATION, 19b ATTACH PANEL TO PANEL BRACKET

Models: DD60S 7 DD60ST 7

1 23

Page 20


	INTEGRATED MODELS WITH BADGE (GB IE) ONLY - INSTALLING THE FRONT PANEL & BADGE CONTROLS		20


16b DETERMINE BADGE CUTOUT LOCATION		17b REMOVE BRACKET & DISCONNECT BADGE

WARNING!

Electrical Shock Hazard

Before continuing, ensure that the product is disconnected from the power supply.

Failure to follow this warning may result in electrical shock, injury or fire.

127 mm

228.5	mm
	228.5

Badge zone

255 mm

30 mm	25 mm

		4
18b ROUTE BADGE WIRING THROUGH PANEL	19b ATTACH PANEL TO PANEL BRACKET
	There must be at least
	3 screws used each side	2
	1	16 mm x6
	1

2	Align bottom of panel
	with bottom of bracket

Page 20

Image 20

Fisher & Paykel DD60ST 7 16b DETERMINE BADGE CUTOUT LOCATION, 17b REMOVE BRACKET & DISCONNECT BADGE, Badge zone, 228.5

Contents

INSTALLATION INSTRUCTIONS DishDrawerTM dishwasherNZ AU GB IE DD60S 7 & DD60ST 7 modelsSTANDARD HEIGHT SINGLE MODELS 2a SAFETY AND WARNINGS - ALL MODELS IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS Electrical shock hazard3a PARTS SUPPLIED - ALL MODELS OPTIONALExternal Venting kit Panel bracketPanel mounting screws4 PRODUCT DIMENSIONS Product dimensions mmPlan 5CABINETRY DIMENSIONSCabinetry dimensions mm FRONT PANEL SPECIFICATIONS WIDTH OF THE PANELHEIGHT OF THE PANEL min. 2 mmFRONT PANEL SPECIFICATIONS WIDTH OF THE PANELHEIGHT OF THE PANEL min. 2 mm7a CAVITY PREPARATION 10 Water ConnectionWater Pressure Water softener modelsShelf cutouts Shelf cutoutsPower cord excl. plug - 1650 mm Power cord excl. plug - 1650 mmLeft hand side Right hand sidethe prongs engage with the top tabs and it clicks into placeFirmly push the bracket so that 10a ATTACH SIDE MOUNTING BRACKETS ATTACH VENTING HOSE11a INTEGRATED MODELS WITH REMOTE NZ AU ONLY NOW CHOOSE WHICH INSTALLATION METHOD a or b12a PULL THROUGH HOSES & MOVE INTO THE CAVITY 13a SECURE THE DRAWERRepeat for all four brackets10b INTEGRATED MODELS WITH REMOTE NZ AU ONLY 11b PULL THROUGH HOSES & MOVE INTO THE CAVITYATTACH VENTING HOSE ALTERNATIVE METHOD b - SECURE BY DRAWER REMOVAL12b REMOVE THE DRAWER 13b SECURE THE DRAWER TO THE CABINETRY14b REFIT THE DRAWER ONTO THE RUNNERS 15b INTEGRATED MODELS WITH REMOTE NZ AU ONLY16a REMOVE BRACKET FROM PRODUCT 17a ATTACH PANEL TO PANEL BRACKET18a EARTH THE PANEL 19a ATTACH PANEL TO PRODUCT+ or - 2 mm 18b ROUTE BADGE WIRING THROUGH PANEL 16b DETERMINE BADGE CUTOUT LOCATION17b REMOVE BRACKET & DISCONNECT BADGE 19b ATTACH PANEL TO PANEL BRACKET20b REATTACH BADGE & EARTH THE PANEL 21b ATTACH PANEL TO PRODUCTPush the panel in then up to locate24CONNECT INLET HOSE TO COLD WATER 25PLUG PRODUCT INDishwasher using sink trap with drain hose joiner Dishwasher and Standpipe Ø 38 mm26FINAL CHECKLIST 27 TROUBLESHOOTINGSAVE THESE INSTRUCTIONS The dishwasher is beeping continuously

16b DETERMINE BADGE CUTOUT LOCATION

17b REMOVE BRACKET & DISCONNECT BADGE

228.5

Badge zone

18b ROUTE BADGE WIRING THROUGH PANEL

19b ATTACH PANEL TO PANEL BRACKET

3 screws used each side

16 mm x6

Align bottom of panel

with bottom of bracket