Manuals / Fisher & Paykel / Kitchen Appliance / Dishwasher

Fisher & Paykel manual 599082, Models, DD603IH, DS603H, DS603IH, DD603HM, DS603M, DD603M

Models: DS603 I DS603H DS603IH DS603M DD603I DD603IH DD603M DD603HM DD603H DS603

1 47

Page 1

	MODELS
DD603		DD603H
DD603I		DD603IH
DS603		DS603H
DS603 I		DS603IH
DD603M		DD603HM
DS603M		DD603HM

599082

Page 1

Image 1

Fisher & Paykel DS603 I manual 599082, Models, DD603IH, DS603H, DS603IH, DD603HM, DS603M, DD603M

Contents

MODELS 599082DD603H DD603IHPage Changes Fisher & Paykel Customer ServicesC O N T E N T S 3.11 3.103.12 3.13SERVICE PROCEDURES 1.1 Health & Safety 1.0 SERVICE REQUIREMENTS1.1.1 Electrical Safety 1.1.2 Electrostatic Discharge1.1.9 Diagnostics 1.2 Specialised Tools1.1.7 Solvent and Excessive Heat Damage 1.1.8 Sheet Metal EdgesDimensions DIMENSIONS & SPECIFICATIONSSpecifications SpecificationsComponent SpecificationsPart Number Heater Plate NZ/AUS/UK/EU/KR3.1 Chassis 3.0 TECHNICAL OVERVIEW3.2 Drawer Fronts 3.3 Electronics3.4 Motor 3.5 Wiring Cover3.6 Lid System 3.7 Tub3.9 Heating 3.8 Filling3.9.3 Maintaining the Temperature 3.8.1 Water Inlet3.11 Drain Cycle 3.10 Lockring Nut3.12 Filter Plate 3.13 Drying Cycle3.14 Water Softener where fitted 4.1 How to Change Setup Options 4.0 OPTION ADJUSTMENT MODE4.1.2 Rinse Aid Setup rA 4.1.3 Water Supply Hardness Setup hd4.1.7 Clean/dirty Dish Symbol dS 4.1.4 Auto Power Option AP4.1.5 End of Cycle Beeps EC 4.1.6 Closed Drawer Option LdWater Softener Supply Hardness Setuphd where fitted Rinse Aid Setting rAAuto Power Option AP End of Cycle Beeps ECClosed Drawer Option Ld Clean/Dirty Dish Option dSDry Enhancement Option LH Press Power5.1 DishDrawer Diagnostics 5.0 DIAGNOSTICS5.1.2 Optical LED Download / Fault Display 5.1.3 Clearing Fault LogsDeli FastHardware Output 5.1.5 Fast Test Cycle5.1.8 Show Off / Showroom Wash Mode Cycle Count RetrievalThe lid is lifted MarchThe display counts down to zero throughout this cycle The DishDrawer turns off at the end of this cycle6.1 Fault Display/Download Mode 6.0 DIAGNOSTICS QUICK REFERENCE CHARTS6.2 Hardware Output Test Mode Press Power6.3 Fast Test Cycle 6.5 Temperature & Voltage Display Mode6.4 Continuous Cycle Press Power Button Twice7.0 FAULT CODES Fault Code 7.1 Fault Code Description ChartFault LED DisplayF1 The flood switch has been activated for more than 6 seconds 7.2 Fault Code Problem Solving ChartsQuestion Replace wiring harness or repair F3 Water temperature sensed at greater than 85C 185Faround the temperature sensor? Clip hall sensor into stator housingIs the resistance of the temperature F9 Electronics failure EEPROM access errorpower supply for 10 seconds, does element using the connection on theU1 DishDrawer failed to prime with water within approx. 3 minutes may have been refitted since U1 faultQuestion Is the impeller on the rotor slipping?7.4 Poor Wash Performance 7.3 Poor Dry PerformanceCustomers Complaint Food Particles left on Dishes How to resolve the problemmarks not food Customers Complaint Coffee/Tea Stains left in Cupshave a White Chalky film on them Where a Water Softener is not fittedPipe Interrupter Air Break Function C2 Water Softener Brine PumpDetergent or Rinse Aid in the Water Softener Phase 3.5 Dishdrawer Wiring diagram 1 drawer only shown WIRING DIAGRAMConnector Key Electronic Controller9.1 Drawer Front Removal 9.0 SERVICE PROCEDURES9.2 Tub Removal 9.4 Drying Fan Removal 9.3 Drawer and LCD Display Removal9.6 Electronic Controller 9.5 Detergent Dispenser9.9 Wiring Cover Removal 9.8 Rotor Assembly Removal9.7 Filter Plate Removal 9.11 Rotor Sensor Removal 9.10 Tub Disconnectionelectronic 9.12 Locking Ring, Element Plate and Motor Assembly Removal 9.14 Yoke Removal 9.13 Lid Removal9.15 Lid Actuator Removal 9.17 Chassis Circuit Board / Flood Sensor Removal 9.16 Slide Rail Replacement9.18 Water Valve Removal 9.19 Fill Hose, Drain Hose, Wiring Harness Replacement9.21 Toe Kick Removal 9.20 Link Support Replacement9.22 Lower Tub Cowling 9.24 Water Softener 9.23 Front Trim Replacement