Fluke 1504 - page 11

Phone: +1.801.763.1600

Telefax: +1.801.763.1010

E-mail: support@hartscientific.com

FlukeNederland B.V.

Customer Support Services

Science Park Eindhoven 5108

5692 EC Son

NETHERLANDS

Phone: +31-402-675300

Telefax: +31-402-675321

E-mail:ServiceDesk @fluke.nl

FlukeInt'l Corporation

Service Center - Instrimpex

Room 2301 Sciteck Tower

22 Jianguomenwai Dajie

Chao Yang District

Beijing 100004, PRC

CHINA

Phone: +86-10-6-512-3436

Telefax: +86-10-6-512-3437

E-mail:xingye .han@fluke.com.cn

Fluke South East Asia Pte Ltd.

FlukeASEAN Regional Office

Service Center

60 Alexandra Terrace #03-16

The Comtech (Lobby D)

118502

SINGAPORE

Phone: +65 6799-5588

Telefax: +65 6799-5588

E-mail:antng @singa.fluke.com

1 Before You Start

Authorized Service Centers

Contents

Main Rev. 571202 Table of Contents ii 7.3 Remote Commands . . . . . . . . . . . . . . . . . . . . . . . . . 28 8 Calibration Procedure . . . . . . . . . . . . . . . . . . . . . . 35 Page Page 1 Before You Start 1.1 Symbols Used 1.2 Safety Information 1.2.1 Warnings Page 1.2.2 Cautions 1.3 Authorized Service Centers Page Page 2 Introduction 3 Specifications and Environmental Conditions 3.1 Specifications 9 3 Specifications and Environmental Conditions Specifications 3.2 Environmental Conditions 4 Quick Start 4.1 Unpacking 4.2 Power 4.3 Connecting the Probe 4.4 DC Power Option + Page 5 Parts and Controls 5.1 Front Panel Buttons 84.9814 C 5.2 Rear Panel l 6 General Operation 6.1 Selecting Units 6.2 Parameter Menus 6.3 Menu Lockout Page 6.4 Selecting the Probe Characterization 6.4.1 Setting the Probe Characterization Type Pr= thr Pr= rtd 6.4.2 Setting the Characterization Coefficients b0 +4.336079 E -04 6.4.3 Steinhart-Hart Characterization () [] 6.4.4 Callendar-Van Dusen (RTD) Conversion The RTDconversion uses the Callendar-VanDusen equation: [] ()() () 6.4.5 Testing the coefficients 6.5 Filtering Page 7 Digital Communications Interface 7.1 Serial Interface 7.1.1 Setting the Baud Rate 7.1.2 Automatic Transmission of Measurements 7.1.3 Time Stamp and System Clock 7.1.4 Duplex Mode and Linefeed 7.2 GPIB Interface 7.2.1 Setting the Address 7.2.2 Setting the Termination Character 7.2.3 Time Stamp 7.3 Remote Commands 7.3.1 Measurement Commands 29 7 Digital Communications Interface Remote Commands Table 5 Command List , n Page 7.3.2 Probe Characterization Commands 7.3.3 Sample Commands 7.3.4 Communication Commands 7.3.5 Calibration Commands 7.3.6 Other Commands 8 Calibration Procedure 8.1 Accessing the Calibration Parameters 8.2 Calibration Procedure 9 Maintenance 10 Troubleshooting 10.1 CE Comments 10.1.1 EMC Directive 10.1.2 Low Voltage Directive (Safety)