Applicable Drawings and Bill of Materials | Fluke 875 specification

Appendix	C
Applicable Drawings and Bill of Materials

Appendix C

Applicable Drawings and Bill of Materials

C.1 Applicable Drawings

Document Number	Description
GEL876-1-55	Rack Chassis & Recommended Seismic Mtg.
GEL876A-1	Readout Module Dimensional Outline
GEL875-1	Interconnection Diagram High-Range Containment Monitor
GEL-877-1	High-Range Detector & Bracket Dimensional Outline
876-1-114	Support Strap
844-8-5	Blank Panel Assembly
876-1-55	Rack Chassis
876A-1-108	High Range Containment Monitor Readout Assembly
876A-1-86	Preamp/Meter PC Board Assembly
876-1-100	Preamp Shield Assembly
876A-1-3E	Schematic Preamp Meter PC Board
876A-1-92	High-Range CAM ECS PC Board Assembly
876A-1-3D	Schematic ECS PC Board
876-1-89	Power Supply PC Board Assembly
876-1-3C	Schematic Power Supply PC Board Assembly
876-1-89A	Voltage Regulator PC Board Assembly
876-1-93A	Schematic, Regulator PC Board Assembly
876A-1-75A	Relay Driver PC Board Assembly
876A-1-3B	Schematic Relay Driver PC Board
876-1-104	Switch PC Board Assembly
876-1-3J	Schematic PC Switch Board
876-1- 78	Mother PC Board Assembly
876-1-3A	Schematic Mother PC Board

Document Number	Description
876-1-107	Rear Panel Assembly
876-1-85	Rear Panel Assembly

C-1

Image 47

Fluke 875 manual Applicable Drawings and Bill of Materials, Document Number Description

Contents

High Range Containment Monitor Victoreen Fluke Biomedical Table of Contents Calibration and Test Procedures Containment Monitor SpecificationsIntroduction General Description Readout Module 876A-1 Temperature Operating 40 to 120F 4 to 49C Rack Chassis Equipment OverviewHigh-Range Containment Monitor Detector Optional Equipment Pull Box AssemblyCables/Connectors/Panel Flexible Tubing 878-12-30TAB High-Range Containment Monitor Typical Energy Response Curve Detector Typical Linearity Detector Receiving Inspection High-Range Detector, Recommended Installation Storage Procedures, Warnings, and Cautions Blank Pull Box InstallationInstallation Readout Module Cable Sealing Specifications for Cable Detector Cable Inside Containment Cable and Wiring InstallationDetector Test After Installation Specifications for Cable Computer & Recorder Ancillary WiringAll Alarms on P2 Normal Operation Shelf State Power Connections P1 Operation Operation Victoreen Readout Module 876A-1 Function DescriptionFunctional Description Negative Power Supply Operation of High Voltage Supply During ECS Test High Voltage Power Supply Normal Operation non-ECS TestFAIL/SAFE Comparison Circuit on Power Supply Board Alert Alarm Circuit High Alarm Circuit Pen Clamp Fail/Safe CircuitRecorders and Computer Buffers Meter at extreme lower end of scale Panel Meter Action During ECS Test Monitoring Circuits of The ECS Board Action of Green Safe/Reset Light and Alarm During ECS TestLow Voltage Ramp Generator Block Diagram of ECS Test Muting Circuits of ECS Board Safe/Reset Sub-circuits Blank Calibration Maintenance, Calibration, and TroubleshootingMaintenance Test Procedure TP876A-1-108 Troubleshooting Rear Panel Signal Input CircuitMother Board P/N 876-1-78, Schematic 876-1-3A PreamplifierIMeter Board P/N 876A-1-86, Schematic 876A-1-3E Test Point Normal Channel Test TP501 TP502 +6.3 Normal Low Signal Level Channel Test High Alarm CircuitMuting Stages of the Alarm Circuits ESC Board P/N 876A-1-92, Schematic 876A-1-3D Wave Shapes on the Electronic Check Source Board Starting With Terminal H on Relay Driver Board Starting With Pins M and P on the Power Supply SchematicOverall Fail Circuitry Associated with the ECS Test Operation of the Latch Circuit Outputs of U206 Pulse Generator on the ECS Board Circuit assumed initially in Pass Condition Fail Condition Latch Circuit Pin Voltage State Comments NOR Calibration and Test Procedures Blank Cable and Pull Box Procedures Cable and Pull Box Procedures Victoreen Document Number Description Applicable Drawings and Bill of MaterialsApplicable Drawings Detector Cable Out of Containment Applicable Bill of Materials Fluke Biomedical