Fortress Technologies ecure Wireless Access Bridge - page 27

Fortress Wireless Access Bridge: Installation

17

Slide the compression nut, with the threaded opening

facing toward the connector, over the connector and

onto the cable.

CAUTION: There

are four different

possible alignments be-

tween the RJ-45 connec-

tor and the connector

boot. If the boot and

connector are not in the

correct alignment, the

RJ-45 connector will not

plug into the Bridge’s

WAN p ort .

Slide the compression bushing over the connector and

onto the cable.

Slide the threaded coupler, with the flanged end facing

toward the compression nut and bushing, over the

connector and onto the cable.

With the smooth-side prongs on the two halves of the

connector collar facing out and aligned with the RJ-45

connector’s locking tab, fit the collar around the

connector so that the connector’s locking tab is

compressed (the contact end of the connector extends

approximately 1/2" from the collar). Fit the outer tabs on

one half of the connector collar into the slots of the

other, and squeeze the two halves of the connector

collar together until they snap into place.

NOTE: Plugging

the connector/boot

into the

WAN port is de-

scribed in Step 4 of Sec-

tion 2.4.5.

Align the primary key tab on the inner ring of the

connector boot with the cable connector’s locking tab.

Maintaining this alignment, fit the RJ-45 connector-

collar assembly into the boot through the boot’s

threaded end and snap the collar tabs into the boot

slots. Screw the connector boot securely onto the

threaded coupler.

WARNING: To

avoid the risk of

severe electrical shock,

do not remove t he cover

plate while the Fortress

Bridge is out of doors.

Fit the compression bushing into the flanged end of the

threaded connector, and fit the compression nut over

the flanges. Screw the compression nut securely onto

the threaded connector until the bushing is compressed

around the cable to provide a water seal.

2Attach the cover plate to the Bridge’s front panel with the

plate’s three captive screws, as shown in Figure 2.3.

3If only one antenna will be attached to the Bridge, screw the

antenna port cap onto the unused antenna port.

Figure 2.3 Attaching the Front-panel Cover Plate

Contents

Main Page Fortress Bridge i Page Table of Contents 1 Introduction 1 2 Installation 6 Indoor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3 Configuration 21 The Bridge GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Radio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4 Administration 52 5 Monitoring and Diagnostics 68 6 Command-Line Interface 80 Administration in the Bridge CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Monitoring and Diagnostics in the CLI . . . . . . . . . . . . . . . . . . . . . .101 WLAN Wireless Extension Tools . . . . . . . . . . . . . . . . . . . . . . . . . .104 Page Chapter 1 Introduction 1.1 Fortress Secure Wireless Access Bridge 1.1.1 Management Interfaces 1.2 Network Security Overview 1.3 The Fortress Security System 1.3.1 Multi-factor Authentication 1.3.2 Strong Encryption at the MAC Layer 1.3.3 System Components 1.3.4 Operating Modes Page 1.4 This Document 1.4.1 Document Conventions 1.4.2 Related Documents Chapter 2 Installation 2.1 Introduction 2.1.1 System Requirements 2.1.2 Compatibility 2.2 Preparation 2.2.1 Shipped and Optional Parts Page Page Page 2.3 Installation Instructions 2.4 Outdoor Installation 2.4.1 Connecting the Bridge for Preconfiguration 2.4.2 Preconfiguring the Bridge for Outdoor Operation Page Page Page 2.4.3 Weatherizing the Bridge To install the Weatherizing Kit: Page 2.4.4 Mast Mounting the Bridge To install the Mast-Mounting Kit: 2.4.5 Reconnecting the Bridge for Outdoor Operation 2.5 Indoor Installation 2.5.1 Connecting the Bridge for Indoor Operation 2.5.2 Configuring the Bridge for Indoor Operation Chapter 3 Configuration 3.1 The Bridge GUI 3.1.1 User Accounts 3.1.2 Accessing the GUI To access the Bridge GUI: 3.2 LAN Settings 3.2.1 Spanning Tree Protocol 3.2.2 WAN Port Encryption To reconfigure Bridge LAN settings: 3.3 Radio Settings 3.3.1 Radio State, Band and Mode Settings 3.3.2 Radio Transmission and Reception Settings Page Page 3.3.3 Configuring Basic Radio Settings 3.3.4 Virtual Radio Interface Settings Page Page Cleartext Security Fortress Security Open WEP and Shared WEP 802.1X Security WPA, WPA2 and WPA-Mixed Security WPA-PSK, WPA2-PSK and WPA-Mixed-PSK Security 3.4 802.1X Server and LAN Port Settings 3.4.1 802.1X Authentication Server To configure the Bridge for use with an external 802.1X authentication server: 3.4.2 LAN Port 802.1X Settings 3.5 Bridge Passwords Page 3.6.1 Operating Mode To change the Bridge operating mode: 3.6.2 Secure Shell Access To configure SSH access to the Bridge CLI: 3.6.3 Encryption Algorithm To change the Bridge encryption algorithm: 3.6.4 Re-keying Interval To change the Bridges re-keying interval: 3.6.5 Access ID To change the Bridges Access ID 3.6.6 Non-802.1X Authentication Global and Default Settings To enable/disable all authentication: To configure an external RADIUS server: To enable/disable device authentication: To configure maximum authentication attempts: To enable/disable user session timeout login prompts: To configure default idle and session timeouts for authenticated users: To configure the default user authentication and device state for authenticating devices: 3.7 Blackout Mode To enable/disable blackout mode: 3.8 System Date and Time To change the date and time on the Bridge: 3.9 Restoring Default Settings 3.10 Front-Panel Operation 3.10.1 Mode Selection from the Front Panel Page 3.10.2 Rebooting the Bridge from the Front Panel 3.10.3 Restoring Defaults from the Front Panel Chapter 4 Administration 4.1 Device Authentication 4.1.1 Maximum Device Authentication Retries 4.1.1 Default Device Authentication Settings 4.1.2 Individual Device Authentication Settings To edit a device: To delete one or more devices: 4.2 User Authentication 4.2.1 Maximum User Authentication Retries 4.2.1 Default User Authentication Settings 4.2.2 Individual User Authentication Settings To add a user: To edit a user account: To delete a user account: 4.3 Trusted Devices 4.3.1 Adding Trusted Devices To add a Trusted Device: 4.3.1 Editing Trusted Devices 4.3.2 Deleting Trusted Devices 4.3.3 Visitor Access through Trusted Devices 4.4 SNMP Settings 4.4.1 Configuring SNMP 4.5 Backing Up and Restoring Page 4.5.1 Backing Up the Bridge Configuration 4.5.2 Restoring from a Backup File 4.6 Software Versions and Upgrades 4.6.1 Viewing Current Software Version 4.6.2 Upgrading Bridge Software Page 4.7 Rebooting the Bridge Page 5.1.1 Traffic Statistics 5.1.2 Interface Statistics 5.1.3 Radio Statistics 5.2 Tracking Page 5.3 AP Associations 5.4 View Log Page 5.5 Diagnostics 5.5.1 Pinging a Device 5.5.2 Tracing a Packet Route 5.5.3 Flushing the Host MAC Database 5.5.4 Generating a Diagnostics File Page can exhibit: 5.6.2 Radio LEDs The upper LED can exhibit: The lower LED can exhibit: Both upper and lower LEDs can exhibit: All four Radio LEDs can exhibit: 5.6.3 Port LEDs Chapter 6 Command-Line Interface 6.1 Introduction 6.1.1 CLI Administrative Modes 6.1.2 Accessing the CLI through the Serial Port 6.1.3 Accessing the CLI Remotely 6.1.4 Logging On and Off the CLI 6.2 Getting Help in the CLI 6.3 Command Syntax 6.4 Configuration in the Bridge CLI 6.4.1 LAN Settings in the CLI 6.4.2 Spanning Tree Protocol in the CLI associated with the Bridges antenna port 1 (ANT1), while , at which point the Bridge Mode option will be inserted dynamically, as shown below. Page Page Page 6.4.4 Bridge Passwords in the CLI 6.4.5 Security Settings in the CLI Page Page Page 6.4.6 System Date and Time in the CLI 6.4.7 Restoring Default Settings in the CLI 6.4.8 Non-802.1X Authentication Settings in the CLI Page 6.4.9 802.1X Authentication Settings in the CLI Page 6.5 Administration in the Bridge CLI 6.5.1 Trusted Devices in the CLI 6.5.2 SNMP Settings in the CLI 6.5.3 Viewing the Software Version in the CLI 6.5.4 Restarting the Bridge in the CLI 6.6 Monitoring and Diagnostics in the CLI 6.6.1 Viewing a Summary Overview of the Bridge 6.6.2 Viewing System Uptime in the CLI 6.6.3 Partners Tracking in the CLI 6.6.4 Host Tracking in the CLI 6.6.5 AP Associations in the CLI 6.6.6 Viewing the System Log in the CLI 6.6.7 Pinging a Device 6.6.8 Tracing a Packet Route 6.7 WLAN Wireless Extension Tools 6.7.1 Creating a Wireless Extension Tools Script 6.8 Secure Automatic Configuration 6.8.1 Preconfiguring a New Network Deployment with SAC Page Page 6.8.2 Reconfiguring Network Settings with SAC Page 6.8.3 Adding and Deleting Network Bridges with SAC Page Page Fortress Bridge: Fortress Security System Overview 114 Chapter 7 Specifications 7.1 Hardware Specifications 7.1.3 Environmental 7.1.1 Performance 7.1.2 Physical Fortress Bridge: Fortress Security System Overview 7.2 RJ-45-to-DB9 Console Port Adapter Logical Interface Physical Interface Page Chapter 8 Troubleshooting Page Index Page Page Page Page Page Page Page Page Glossary Rijndael algorithm Fortress Secure Wireless Access Bridge Fortress Secure Client Fortress Security Controller Layer 2 OSI Layer 2 Data Link Layer fails over SCB Fortress Security Gateway Bridge Fortress Page Information Technologies Access ID packet Fortress Secure Client Bridge Fortress Secure Client Fortress Security Gateway Fortress Secure Client Bridge