The controller has three error display messages:

, indicating a heating problem or drain valve problem. Turn the fryer off reset the drain handle and try again. If the error still appears, call the Frymaster hotline.

and actual frypot temperature, indicating that the shortening temperature is above 411°F (210°C). If this display is seen, turn the fryer off immediately and contact an authorized service center.

, indicating that the controller has detected a problem in the temperature measuring circuits and control circuits. Turn the fryer off and contact an authorized service center.

NOTE: This controller is configured for the fryer on which it installed (i.e., gas or electric and full- or split-pot). Although identical in appearance, controllers configured for use on one type of fryer are not interchangeable with those configured for use on another type.

CONTROLLER OPERATING INSTRUCTIONS

1.Turn the controller on by pressing the ON/OFF switch .

The controller software version number will display for four seconds then, in non-CE units, the setpoint temperature will appear in the display. In CE units, the frypot temperature will appear in the display – to view the setpoint temperature, press the temperature switch for the frypot in question.

A decimal point will appear between the first two numbers of the display, indicating that the unit is heating. When the frypot has reached the setpoint temperature, the heat indicator decimal point will go out, indicating that the fryer is ready for cooking.

2.Adjust the setpoint if necessary. To raise the setpoint temperature, press an up arrow . Press a down arrow to lower the setpoint temperature.

The display will change at the rate of approximately one-degree per second initially. If the arrow is pressed and held, after a change of about 12°, the rate of change will increase, allowing large changes in setpoint temperature to be made quickly.

SELECTING FAHRENHEIT OR CELSIUS DISPLAY MODE

To toggle the temperature display between Fahrenheit and Celsius, press the right C/F switch . The display(s) will change from xxx°F to xxx°C, where “xxx” is the frypot or setpoint temperature.

CANCELING THE MELT-CYLE

DANGER

Do not cancel the melt-cycle mode if using solid shortening!

The melt-cycle is designed to prevent scorching shortening and overheating the frypot or elements while gradually melting blocks of shortening. The controller automatically starts the fryer in the

3–4

Page 15 Page 17
Page 16
Image 16
Frymaster E4 manual Controller Operating Instructions, Do not cancel the melt-cycle mode if using solid shortening
Page 15 Page 17

E4 specifications

The Frymaster E4 is an advanced fryer that represents the cutting edge of commercial frying technology. Designed for efficiency and performance, it is favored by restaurants and fast-food chains looking to optimize their cooking processes while maintaining exceptional food quality.

One of the standout features of the Frymaster E4 is its programmable controls. With an intuitive digital interface, operators can easily adjust cooking temperatures, times, and even recipes with just a few taps. This level of precision ensures that food is consistently cooked to perfection every time, reducing waste and improving overall efficiency in the kitchen.

The E4 is equipped with high-performance burners that ensure rapid heating and recovery times. This means that cooking oil reaches the desired temperatures quickly, allowing for faster frying cycles. Thus, busy kitchens can meet high-demand periods without compromising quality or service speed. The fryer also features a high-efficiency oil filtration system that automatically removes contaminants and prolongs the life of the frying oil, resulting in a significant reduction in operating costs over time.

Another notable technology in the Frymaster E4 is its oil level management system, which actively monitors oil levels and alerts the operator when replenishment is necessary. This feature prevents overfilling or underfilling, both of which can negatively impact cooking performance and food quality.

Safety is also a top priority with the E4, as it incorporates features such as a built-in safety shut-off mechanism that activates if the temperature exceeds safe levels. Additionally, the fryer's robust construction minimizes the risks of spills and accidents in the kitchen, making it a reliable choice for high-traffic environments.

The Frymaster E4 also emphasizes energy efficiency, designed to meet stringent energy-saving standards without compromising performance. This is crucial in the current market, where energy costs can significantly impact overall profitability.

In conclusion, the Frymaster E4 offers an impressive combination of innovative technology, safety, and efficiency. Its programmable controls, high-performance frying capabilities, and advanced filtration and oil management systems make it an essential tool for any commercial kitchen aiming to enhance productivity and food quality. As the demands of the food industry continue to grow, the E4 stands out as a reliable partner for chefs looking to elevate their frying operations.
Top Page Image Contents