2.On dual-vat fryers, and on full-vat fryers where the temperature probe is attached to the element being replaced, disconnect the wire harness containing the probe wiring. Using a pin pusher, disconnect the probe wires from the 12-pin connector C-6.

3.In the rear of the fryer directly behind the frypot disconnect the 6-pin connector for the left element (as viewed from the front of the fryer) or the 9-pin connector for the right element. Press in on the tabs on each side of the connector while pulling outward on the free end to extend the connector and release the element leads (see photo below). Pull the leads out of the connector and out of the wire sleeving.

Note: Liquid resistant seals.

4.Raise the element to the full up position and support the elements.

5.Remove the hex head screws and nuts that secure the element to the tube assembly and pull the element out of the frypot. NOTE: Full-vat elements consist of two dual-vat elements clamped together. For full-vat units, remove the element clamps before removing the nuts and screws that secure the element to the tube assembly.

6.If applicable, recover the probe bracket and probe from the element being replaced and install them on the replacement element, then install the replacement element in the frypot, securing it with the nuts and screws removed in Step 5 to the tube assembly ensuring the gasket is between the tube and element assembly.

7.Route the element leads through the element tube assembly and into the wire sleeving to prevent chafing. Ensure that the wire sleeving is routed back through the Heyco bushing keeping it clear from the lift springs. Also ensure that the wire sleeving extends into the tube assembly to protect the edge of the tube assembly from chafing the wires. Press the pins into the connector in accordance with the diagram below, and then close the connector to lock the leads in place. NOTE: It is critical that the wires be routed through the sleeving to prevent chafing.

7-5

Page 35 Page 37
Page 36
Image 36
Frymaster E4 manual
Page 35 Page 37

E4 specifications

The Frymaster E4 is an advanced fryer that represents the cutting edge of commercial frying technology. Designed for efficiency and performance, it is favored by restaurants and fast-food chains looking to optimize their cooking processes while maintaining exceptional food quality.

One of the standout features of the Frymaster E4 is its programmable controls. With an intuitive digital interface, operators can easily adjust cooking temperatures, times, and even recipes with just a few taps. This level of precision ensures that food is consistently cooked to perfection every time, reducing waste and improving overall efficiency in the kitchen.

The E4 is equipped with high-performance burners that ensure rapid heating and recovery times. This means that cooking oil reaches the desired temperatures quickly, allowing for faster frying cycles. Thus, busy kitchens can meet high-demand periods without compromising quality or service speed. The fryer also features a high-efficiency oil filtration system that automatically removes contaminants and prolongs the life of the frying oil, resulting in a significant reduction in operating costs over time.

Another notable technology in the Frymaster E4 is its oil level management system, which actively monitors oil levels and alerts the operator when replenishment is necessary. This feature prevents overfilling or underfilling, both of which can negatively impact cooking performance and food quality.

Safety is also a top priority with the E4, as it incorporates features such as a built-in safety shut-off mechanism that activates if the temperature exceeds safe levels. Additionally, the fryer's robust construction minimizes the risks of spills and accidents in the kitchen, making it a reliable choice for high-traffic environments.

The Frymaster E4 also emphasizes energy efficiency, designed to meet stringent energy-saving standards without compromising performance. This is crucial in the current market, where energy costs can significantly impact overall profitability.

In conclusion, the Frymaster E4 offers an impressive combination of innovative technology, safety, and efficiency. Its programmable controls, high-performance frying capabilities, and advanced filtration and oil management systems make it an essential tool for any commercial kitchen aiming to enhance productivity and food quality. As the demands of the food industry continue to grow, the E4 stands out as a reliable partner for chefs looking to elevate their frying operations.
Top Page Image Contents