Fujitsu FI-6000NS 3.5 Setting the IP Address/DHCP

5.Select whether "Daylight Savings Time" should be on or off.

This option is not shown for timezones where daylight savings time is not used.

6.Press the [OK] button.

⇒The Region/Timezone is set. Continue with IP address/DHCP settings.

3.5 Setting the IP Address/DHCP

An IP address must be set in order to connect the scanner to a network.

Do not use an IP address that already

ATTENTION	exists in the network.
	exists in the network.
	IP address duplication will cause an
	error during setup.

1.Select the [Network Settings] tab on the top menu.

2.Select the [IP Address] tab on the left side menu.

⇒The IP address/DHCP screen appears.

3.Set the scanner's IP address. This may be done automatically, by pressing the DHCP [On] button.

The IP address may also be set manually, by pressing the DHCP [Off] button and entering the following numerical addresses:

•IP Address

•Subnet Mask

•Default gateway

4.Press the [OK] button.

⇒The information entered is set.

If the IP address is the same as one

HINT	already in use, network communication
	already in use, network communication
	problems will occur. In this case, try the
	following steps:

1.Disconnect the LAN cable and turn the scanner off.

2.Reboot the scanner with the LAN cable still disconnected, and enter a non- duplicate IP address.

3.Re-connect the LAN cable to the scanner.

When DHCP is set to "On", the following settings are assigned by the DHCP:

•IP Address

•Subnet Mask

•Default Gateway

•DNS Server

•WINS Server

Even if DNS or WINS server is set, priority is given to the scanner settings over the DHCP settings.

Continue with the DNS settings.

Network Scanner fi-6000NS Getting Started		7
Network Scanner fi-6000NS Getting Started		7

Contents

Page Page Chapter Chapter 2 Setting up the Scanner Chapter 3 Setting up for Network Use Downloading the Manual Appendix A Calibrating the Touch Panel Appendix B Scanner Care Appendix C Replacing Consumable Parts Appendix D Network Connection Troubleshooting Copyright Page Page WinDump3.9.5 Introduction Use in High-safetyApplications About the Use of Mercury LCD Peculiarities Replacing Batteries Trademarks Manufacturer Symbols Used in This Manual About Maintenance Warning Indications Used in This Manual Warning Label ■Safety Precautions Do not damage the AC cable Use only specified AC cables and connector cables Do not touch the AC cable with wet hands Wipe any dust from the power plug Do not install the scanner on unstable surfaces Do not block the ventilation ports Do not place heavy objects or climb on top of the scanner Firmly insert the power plug Avoid any contact when scanner is in use Page Chapter 1 Scanner Features 1.1 Scanner Features 1.2 From Arrival through Operation 1.3 Checking the Contents of the Scanner Package 1.4Names and Functions of Parts Chapter 2 Setting up the Scanner 2.1 Space Requirements 2.2 Installing the Scanner 2.3 Connecting the Cables Chapter 3 Setting up for Network Use 3.1 Logging in 3.2Changing the Administrator Password 3.3 Setting the Scanner Name 3.4 Setting the Region/Timezone 3.5 Setting the IP Address/DHCP 3.6 Setting the DNS Server 3.7 Setting the WINS Server 3.8Checking the Network Connection 3.9 Restarting the System Chapter 4 Downloading the Manual Chapter 5 Performing a Scan Test ■If Scanning Completes Successfully ■If Scanning does not Complete Successfully Appendix A Calibrating the Touch Panel Appendix B Scanner Care Appendix C Replacing Consumable Parts Appendix D Network Connection Troubleshooting Appendix D ■Checking Basic Network Operation with a Ping Test ■Failure to Connect to a Remote Computer using its IP Address ■Failure to Connect to a Remote Computer using its Server Name ■Failure to Connect to the Scanner using a Web Browser ■Problems when Connecting to the Scanner using a Web Browser Appendix E Troubleshooting Network Scanner fi-6000NS Getting Started