Fujitsu M3000 CHAPTER 3 Command Reference

C120-E360-06EN 3-1

CHAPTER 3 Command Reference

1

3.1 setrci

•NAME

setrci - configure or display the environment of the remote cabinet interface (RCI)

•SYNOPSIS

setrci -c stat

setrci -c init [-s RCI_network]

setrci -c set host_no

setrci -c initconfig [-s RCI_network]

setrci -c addconfig [-s RCI_network]

setrci -c replaceconfig [ RCI_address]

setrci -c ledon RCI_address

setrci -c ledoff

setrci -c idpin

setrci -h

• DESCRIPTION

The setrci(8) command configures or displays information that accompanies the

initial setting and maintenance of the RCI environment.

The following can be set or displayed:

stat Displays the status of the RCI network.

init Initializes the RCI setting. Initialization is only performed for the host

that executes the command. If there are other hosts connecting to the

RCI, initialization must be performed for each host.

set Sets an RCI address. Use this specification when the RCI setting has been

initialized. After the setting, "-c initconfig" or "-c addconfig" must be

executed.

initconfig Makes the RCI setting on the first host. An RCI I/O unit connected via

RCI is searched for and found, and then an RCI address is assigned.

Contents

Main Page Page Page Page C120-E360-06EN Preface Audience Glossary Structure and Contents of this Manual Page SPARC Enterprise Mx000 Servers Documentation The manuals listed below are provided for reference. Page Page Abbreviated References to Other Documents Models The model names used in this manual are as follows. Text Conventions This manual uses the following fonts and symbols to express specific types of information. Prompt Notations Syntax of the Command-Line Interface (CLI) Command syntax Fujitsu Welcomes Your Comments Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i CHAPTER 2 Setup of the RCI for Operation . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 CHAPTER 3 Command Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Page Page Page Page CHAPTER 1 RCI Overview 1.1 RCI Features 1.2 RCI Functions Page 1.3 RCI Connection Scheme Page Page CHAPTER 2 Setup of the RCI for Operation 2.1 Overview of RCI Setup 2.2 RCI Setup for Initial Installation 2.2.1 RCI setup flow 2 2.2.2 Confirming RCI initialization 2.2.3 Connecting RCI cables 2.2.4 Making an RCI address setting 1 2.2.5 Making an RCI construction setting 1 2.3 RCI Setup for Addition of an RCI I/O Unit 2.3.1 RCI setup flow 2.3.2 Connecting an RCI cable 2.3.3 Making an RCI expansion setting 1 2.4 RCI Setup for Addition of an RCI Base Cabinet 2.4.1 RCI setup flow 2.4.2 Confirming RCI initialization 2 2.4.3 Connecting an RCI cable 2.4.4 Making an RCI address setting 1 2.4.5 Making an RCI expansion setting 1 2.5 RCI Setup for Replacement of an RCI I/O Unit 3 1 2 3 2.5.3 Replacing an RCI I/O Unit 2.5.4 Making an RCI replacement setting 1 2.6 RCI Setup for Replacement of an RCI Base Cabinet 2.6.1 RCI setup flow 2.6.2 Replacing an RCI host 2.6.3 Confirming RCI initialization Page 2.6.6 Making an RCI replacement setting 1 Page Page CHAPTER 3 Command Reference 3.1 setrci of an RCI I/O unit. OPERANDS The following operands are supported: EXTENDED DESCRIPTION zWhen "-c stat" is specified, the following states are displayed: zWhen the RCI state is Active, the following information is displayed after List: Page Page Page EXAMPLE 2: Makes the first RCI setting on the first host in an M8000/M9000 server. EXIT STATUS The following exit values are returned: 3.2 setrcic Page Page CHAPTER 4 Error Status 4.1 setrci error status 4.2 setrcic error status