Manuals / Brands / Photography / Photo Scanner / Fujitsu / Photography / Photo Scanner

Fujitsu P3PC-1932-01EN Chapter2 INSTALLATION OF THE SCANNER, 2.1 Installing the Scanner, 2.2Connecting the Scanner to Your Personal Computer, ■Connecting with the USB Interface Cable

1 28

Download 28 pages, 1.29 Mb

Chapter2 INSTALLATION OF THE SCANNER

2.1 Installing the Scanner

1. Place the scanner at its installation site.

For details on the scanner's dimensions and required installation space, refer to section 7.2 "Installation Specifications" of "fi-5530C2 Oper- ator’s Guide" on the Setup CD-ROM.

2. Attach the ADF paper chute.

Hold the ADF paper chute and insert its tabs into the corresponding slots in the scanner as shown in the figure below.

The Side guides of the ADF paper chute have to face up.

ADF paper chute

Tab

Side guide

2)Connect the AC adapter connector to the scan- ner’s DC inlet.3) Plug the AC cable into the outlet.

The Function Number Display and the LED

HINT	may flash for an instant when plugging the
	may flash for an instant when plugging the
	AC cable into the outlet.

2.2Connecting the Scanner to Your Personal Computer

Connect either with the USB interface cable or the SCSI interface cable.

3. Connect the AC adapter.

ATTENTION

This scanner is provided with two inter- faces: Ultra SCSI and USB 2.0 /1.1. Connect only one of the USB or SCSI interface cable.

ATTENTION

Use only the AC adapter provided by the manufacturer.

■Connecting with the USB Interface Cable

1) Connect the AC cable to the AC adapter.

1.Connect the USB interface cable to the USB interface connector.

fi-5530C2 Image Scanner Getting Started		3

Contents

fi-5530C2Image Scanner Page CONTENTS ■ Regulatory Information ■ Note of Liability ■ Safety Precautions Chapter1 INTRODUCTION ■Regulatory Information FCC declaration Canadian DOC Regulations Bescheimigung des Herstellers / Importeurs ■Note of Liability Use in High-safetyApplications Trademarks How Trademarks Are Indicated In This Manual About the use of mercury Manufacturer About Maintenance Warning Label Warning Indications Used In This Manual Symbols Used In This Manual ■Safety Precautions Do not install the scanner on unstable surfaces Do not block the ventilation ports Do not place heavy objects or stand on top of the scanner Firmly insert the power plug Avoid any contact when scanner is in use Chapter1 PREPARING THE SCANNER 1.1Checking the Contents of the Scanner Package 1.2 Names of Parts ■Front side ■Rear side 1.3 Operator panel ■Indications on the Function Number Display Chapter2 INSTALLATION OF THE SCANNER 2.1 Installing the Scanner 2.2Connecting the Scanner to Your Personal Computer ■Connecting with the USB Interface Cable ■ Connecting with the SCSI Inter face Cable ■Setting the SCSI ID 2.3Installing the Scanner Software ■Preparations ■Installing the FUJITSU TWAIN32 Scanner Driver 4.Insert the Setup CD-ROMinto the CD drive ⇒<SETUP DISK START UP SCREEN> appears Install the driver, following the on-screen instructions When you see the [InstallShield Wizard Com ■Installing the FUJITSU ISIS Scanner Driver ■Installing ScandAll PRO Proceed with the installation, following the on screen instructions When the [InstallShield Wizard Complete] dia log box appears, click the [Finish] button Error Recovery Guide Adobe® Acrobat® 1.Insert the Adobe Acrobat CD-ROMinto the CD-ROMdrive ⇒The [Adobe Acrobat] dialog box appears 3. In the dialog box below, click the [Next] button 2.4Checking Scanner Driver Operation ■Checking the Operation of the Scanner Driver Page 2.5Uninstalling Supplied Programs Appendix1 TROUBLESHOOTING Appendix1 ■Troubleshooting checklist AP-1 AP-2 ■Temporary error ■Device alarm (Permanent error) AP-3 Appendix2 DAILY CARE ■Locations and Cycle for Cleaning ■Cleaning Method AP-4 Appendix3 REPLACING CONSUMABLES Appendix3 ■Consumables and Replacement Cycle ■Replacing the Pad ASSY ■Replacing the Pick Roller AP-5 AP-6 fi-5530C2Image Scanner Getting Started