Fujitsu P3PC-1932-01EN 20

9.In the [Scan Settings] dialog box, clear the [Save to file] checkbox.

You only check the operation now, so you

HINT	do not have to save to file.

To use FUJITSU ISIS

On the dialog box below, configure scanning set- tings, and then click the [OK] button.

⇒You are returned to the [Scan Settings] dialog box.

12.Click the [Scan] button.

When you are using FUJITSU TWAIN 32,

HINT	you may see the TWAIN Driver setup dia-
	you may see the TWAIN Driver setup dia-
	log box again. If so, click the [Scan] button
	on the dialog box.

10.Click [Scanner Settings].

⇒A setup dialog box appears for you to config- ure scanner driver settings.

11.Configure scanner settings such as the resolu- tion and paper size.

To use FUJITSU TWAIN 32

On the dialog box below, configure scan settings, and then click the [OK] button.

⇒The document is scanned and the scanned image is displayed in the [ScandAll PRO] window.

If the scanned document image is displayed in the win- dow, it means that the scanner driver is installed prop- erly.

For further information about how to scan documents, refer to "fi-5530C2 Operator’s Guide" contained in the Setup CD-ROM.

12

Contents

fi-5530C2Image Scanner Page CONTENTS ■ Regulatory Information ■ Note of Liability ■ Safety Precautions Chapter1 INTRODUCTION ■Regulatory Information FCC declaration Canadian DOC Regulations Bescheimigung des Herstellers / Importeurs ■Note of Liability Use in High-safetyApplications Trademarks How Trademarks Are Indicated In This Manual About the use of mercury Manufacturer About Maintenance Warning Label Warning Indications Used In This Manual Symbols Used In This Manual ■Safety Precautions Do not install the scanner on unstable surfaces Do not block the ventilation ports Do not place heavy objects or stand on top of the scanner Firmly insert the power plug Avoid any contact when scanner is in use Chapter1 PREPARING THE SCANNER 1.1Checking the Contents of the Scanner Package 1.2 Names of Parts ■Front side ■Rear side 1.3 Operator panel ■Indications on the Function Number Display Chapter2 INSTALLATION OF THE SCANNER 2.1 Installing the Scanner 2.2Connecting the Scanner to Your Personal Computer ■Connecting with the USB Interface Cable ■ Connecting with the SCSI Inter face Cable ■Setting the SCSI ID 2.3Installing the Scanner Software ■Preparations ■Installing the FUJITSU TWAIN32 Scanner Driver 4.Insert the Setup CD-ROMinto the CD drive ⇒<SETUP DISK START UP SCREEN> appears Install the driver, following the on-screen instructions When you see the [InstallShield Wizard Com ■Installing the FUJITSU ISIS Scanner Driver ■Installing ScandAll PRO Proceed with the installation, following the on screen instructions When the [InstallShield Wizard Complete] dia log box appears, click the [Finish] button Error Recovery Guide Adobe® Acrobat® 1.Insert the Adobe Acrobat CD-ROMinto the CD-ROMdrive ⇒The [Adobe Acrobat] dialog box appears 3. In the dialog box below, click the [Next] button 2.4Checking Scanner Driver Operation ■Checking the Operation of the Scanner Driver Page 2.5Uninstalling Supplied Programs Appendix1 TROUBLESHOOTING Appendix1 ■Troubleshooting checklist AP-1 AP-2 ■Temporary error ■Device alarm (Permanent error) AP-3 Appendix2 DAILY CARE ■Locations and Cycle for Cleaning ■Cleaning Method AP-4 Appendix3 REPLACING CONSUMABLES Appendix3 ■Consumables and Replacement Cycle ■Replacing the Pad ASSY ■Replacing the Pick Roller AP-5 AP-6 fi-5530C2Image Scanner Getting Started