Fujitsu S510M ■Operation button, ■Rear view

Paper chute

After opening it, load the documents to be scanned on this part.

Side guide

Adjust the side guides to the width of documents so that the scanned images will not be skewed.

Cover open lever

To open the ADF, pull this lever toward you.

Operation button

Stacker

Before using the stacker, unfold and extend it as shown above.

⇒You can also use the ScanSnap without unfolding the stacker.

■Operation button

SCAN

POWER

[SCAN] button

Press this button to start the scanning.

[Power] button

Turns on/off the power.

Power Indicator

Indicates the power status of the ScanSnap.

Blue (Solid):	Ready
Blue (Blinking):Scanning
Orange (Solid): Error
Light off:	Power off

■Rear view

AC adapter connector

USB connector

Seal (reminds you that the supplied software has to be installed first)

After installing the software, remove this seal.

Security cable slot

Plug a commercially available security cable into this slot (anti-theft).

For the Document Specification, refer to "3.2 Paper Sizes of Documents to be Scanned" in "ScanSnap S510M Operator's Guide" stored in the ScanSnap Setup CD-ROM.

ATTENTION

The ScanSnap is turned on/off in conjunction with the connected computer, or with opening/closing of the paper chute. Ordinary, you can forget about turning on/off the ScanSnap.

11

Contents

Chapter 1 Preparation Chapter 2 Connecting the ScanSnap Chapter 3 How to Use the ScanSnap Chapter 4 Troubleshooting Chapter 6 Consumables Introduction Manufacturer Trademarks How Trademarks Are Indicated In This Manual ScanSnap and the Manuals About Mouse Operations Regulatory Information FCC declaration Canadian DOC Regulations Bescheinigung des Herstellers / Importeurs International ENERGY STAR® Program Use in High-SafetyApplications About the use of mercury Safety Precautions Warning Indications Used in This Manual Symbols Used in This Manual Screen Examples in This Manual About Maintenance About the Hot Surface Hazard Warning Label Page The following illustrates important cautions described in this manual Chapter 1 Preparation 1.1 Using the ScanSnap Manuals 1.2 Names and Functions of Components ■Front view ■Operation button ■Rear view Chapter 2 Connecting the ScanSnap 2.1 Installing the Supplied Software ■Installing Adobe Acrobat ■Installing ABBYY FineReader for ScanSnap ■Installing Cardiris ■Installing ScanSnap Manager 2.2 Connecting the ScanSnap to Your Computer ■Connecting the Power Cable ■Connecting the USB Cable ■Turning the ScanSnap ON Chapter 3 How to Use the ScanSnap 3.1 Scanning Settings 3.2 Scanning Documents 2.Adjust the side guides to the width of the loaded document 3.Press the [SCAN] button ⇒Scanning is started ⇒The ScanSnap Quick Menu appears after scanning 3.3 Scanning with the Carrier Sheet ■Creating Facing Pages in One Image ■Scanning Irregular-shapedDocuments 4. Open the Carrier Sheet and place the document inside Neatly align the top of the material with the top of the Carrier Sheet Center the material so that it is entirely contained in the Carrier Sheet 5.Load the Carrier Sheet onto the ScanSnap •Place the Carrier Sheet so that the back side of it faces up 3.4 Scanning Business Cards using Cardiris 3. Check the image data of the scanned business cards in the Cardiris window The images of each business card are displayed on the right 4.Should there be any recognition errors, correct the data manually Correct misrecognized characters ⇒The following window appears 6. On the [Format:] pop-upmenu, select "Address Book 7.Click the [OK] button 8.Click the [Send] button or select [Process] - [Send] on the menu bar 9. On the menu bar, select [Cardiris] - [Quit Cardiris] to quit Cardiris Chapter 4 Troubleshooting 4.1 Clearing Paper Jams 4.2 Troubleshooting Checklist The latest information, which is updated on an Chapter 5 Daily Care 5.1Cleaning Materials 5.2 Cleaning the ScanSnap Exterior 5.3 Cleaning Inside of the ScanSnap 5.4 Cleaning the Carrier Sheet Chapter 6 Consumables 6.1Part Numbers and Replacement Cycle of Consumables 6.2 Purchasing the Carrier Sheet