TROUBLE-SHOOTING GUIDE
SYMPTOM | POSSIBLE CAUSE |
| CORRECTIVE ACTION |
|
| ||
• POWER lamp does not illuminate | Laminator not connected to | Insert attachment plug into receptacle. | |||||
when ON/OFF switch is in the ON | electrical supply. |
|
|
|
|
| |
position. |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
• Heat rollers do not turn. | Circuit breaker open. |
| Reset circuit breaker. |
|
| ||
|
| Safety shield in upright position. | Lower safety shield. |
|
| ||
|
| Feed tray interlock pin not in place. | Slide interlock lever all the way into the left side frame. | ||||
• Laminated items exhibit curling. | Tension between the top and bottom | Adjust tension per section FILM TENSION ADJUSTMENT. | |||||
|
| film roll is unequal. |
|
|
|
|
|
|
| Tension on top or bottom roll of | Adjust tension per section FILM TENSION ADJUSTMENT. | ||||
|
| film is too loose. |
|
|
|
|
|
|
| Speed setting too slow. |
| Slightly speed up laminator. |
|
| |
|
| Bottom film roll may be improperly | Make sure bottom roll of film is around idler bar. | ||||
|
| loaded. |
|
|
|
|
|
|
|
|
|
| |||
• Adhesive deposited on heat rollers. | Top and bottom film webs not | Align film webs per section FILM ALIGNMENT PROCEDURE. | |||||
|
| aligned. |
|
|
|
|
|
|
| Laminate improperly loaded. | Adhesive (matte) side of laminate film may be against the heat | ||||
|
|
|
| rollers. Load film per procedure outlined in section | |||
|
|
|
| FILM LOADED & THREADING. |
|
| |
• Unsatisfactory adhesion of laminate. | Speed setting too fast for type of | Lower speed setting by pressing SLOW button to slower speed | |||||
|
| material being laminated. |
|
|
|
|
|
|
| Insufficient heat. |
| READY LED lamp must be illuminated. | |||
|
| Laminate improperly loaded. | Adhesive side of film must be facing away from the heat rollers. | ||||
|
|
|
| Bottom roll of film not threaded behind the idle bar. | |||
|
| Heat rollers require cleaning. | Clean heat rollers per procedure in section | ||||
|
|
|
| CARING FOR THE GBC CATENA SERIES LAMINATOR. | |||
|
| Laminated item unsuitable for | Item may be dirty or may have | ||||
|
| adhesion. |
| extremely difficult to laminate. |
|
| |
|
|
|
|
|
|
|
|
| SPECIFICATIONS |
|
|
|
|
|
|
| Model | Catena 35 | Catena 65 |
| Catena 105 |
|
|
| Operating Speed: | 1.5 fpm (45.6 cm) | 1.5 fpm (45.6 cm) | 1.5 fpm (45.6 cm) |
|
| |
|
| to 5 fpm (1.6 m) | to 5 fpm (1.6 m) | to 5 fpm (1.6 m) |
|
| |
| Dimensions: |
|
|
| Without Stand | With Stand |
|
| Width: | 24" (62 cm) | 35" (84 cm) |
| 51" (125 cm) |
|
|
| Height: | 12" (31 cm) | 12" (31 cm) |
| 17" (41 cm) | 48" (115 cm) |
|
| Depth: | 21" (53 cm) | 21" (53 cm) |
| 21" (53 cm) |
|
|
| Weight: | 55 lb. (25 kg.) | 84 lb. (38 kg.) | 154 lb. (70 kg.) |
|
| |
| Electrical Requirements: |
|
|
|
|
|
|
| Voltage: | 120V ~ 60 Hz | 120V ~ 60 Hz | 230V ~ 60 Hz |
|
| |
| Current: | 9 Amps | 9 Amps |
| 10.5 Amps |
|
|
| Power: | 1080 W | 1400 W |
| 2310 W |
|
|
| U.S. Receptacle | NEMA | NEMA |
| NEMA |
|
|
| Requirement |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SERVICE AGREEMENT
GBC’s Equipment Maintenance Agreement will insure the quality performance and long life built into your laminator.
A service charge for travel time, labor and parts may be incurred for each out of warranty service call. GBC’s Equipment Maintenance Agreement decreases these expenses and protects your valuable investment. GBC offers several types of agreements to suit your needs and budget. To contact GBC write to:
GBC NATIONAL SERVICE | IN CANADA: | GBC NATIONAL SERVICE |
ONE GBC PLAZA |
| 49 RAILSIDE ROAD |
NORTHBROOK, IL 60062 U.S.A. |
| DON MILLS, ONTARIO |
1.847.272.3700 |
| M3A 1B3 |
Part Number |
|
|
44
