~ift-Off Oven Door

The oven door is

 

removable, but it is

 

heavy. You may need help

 

removing and replacing

 

the door. Do not lift the

 

door by the handle. This

 

can cause the glass to

 

break or can cause

 

damage to the door.

I

To remove the door,

open it a few inches to the special stop position that

will hold the door open. Grasp firmly on each side and lift the door strtiight up and off the hinges.

NOTE:

●Be careful not to place hands between the hinge and the oven door frame as the hinge could snap back and pinch fingers.

●While working in the oven area, cover the hinges with towels or empty paper towel rolls to prevent pinched fingers and chipping the porcelain enamel on the frame.

To replace the door, make sure the hinges are in the special stop position. Position the slots in the bottom the door squarely over the hinges. Then lower the or slowly and evenly over both hinges at the same time. If hinges snap back against the oven frame, pull

them back out.

TO CLEAN THE DOOR:

Inside of the door:

●Because the area inside the gasket is cleaned during the self clean cycle, you do not need to clean this by hand. Any soap left on the liner causes additional stains when the oven is heated.

●The area outside the gasket can be cleaned with a soap-filled scouring pad.

●Do not rub or clean the door gasket—the fiberglass material of the gasket has an extremely low resistance to abrasion. An intact and well-fitting oven door gasket is essential for energy-efficient oven operation and good baking results. If you notice the gasket becoming worn, frayed or damaged in any way or if it has become displaced on the door, you should have it replaced.

NOTE: The gasket is designed with a gap at the bottom to allow for proper air circulation.

Inside Gasket

Gasket

Outside Gasket

Outside of the door:

●Use soap and water to thoroughly clean the top, sides and front of the oven door. DO NOT let water run down through openings in the top of the door. Rinse well. You may also use a glass cleaner to clean the glass on the outside of the door.

●Spillage of marinades, fruit juices, tomato sauces and basting materials containing acids may cause discoloration and should be wiped up immediately. When surface is cool, clean and rinse.

●Do not use oven cleaners, cleansing powders or harsh abrasives on the outside of the door.

((’(lilrit?Ltf,(l )1(,.4’/ /7(1,?1)

35

Page 34 Page 36
Page 35
Image 35
GE 164D2966P126 warranty ~ift-Off Oven Door, Oven door is Removable, but it is, To remove the door, Inside of the door
Page 34 Page 36

164D2966P126 specifications

The GE 164D2966P126 is a critical component in the realm of industrial and aerospace applications, offered by General Electric. This part exemplifies advanced engineering designed to fulfill high-performance requirements in demanding environments. Its reliability and efficiency make it suitable for a variety of uses, with a particular focus on power generation and distribution systems.

One of the main features of the GE 164D2966P126 is its robust construction. Built to withstand extreme operating conditions, this part demonstrates exceptional durability in the face of thermal fluctuations, pressure variations, and mechanical stresses. This resilience is essential for components utilized in the aerospace industry, where failure is not an option.

The technology integrated into the GE 164D2966P126 is another standout characteristic. With advancements in materials science, the component is manufactured using lightweight yet strong materials that contribute to overall efficiency. This approach minimizes weight without compromising structural integrity, which is crucial in aviation applications where every ounce matters.

Additionally, the GE 164D2966P126 employs cutting-edge manufacturing techniques that ensure precision and quality. The use of CNC machining and additive manufacturing processes enhances the component's design flexibility while maintaining tight tolerances. This precision is vital for parts that must fit seamlessly within complex systems.

The electrical characteristics of the GE 164D2966P126 are optimized to handle varying loads, making it an indispensable part of electrical control and distribution systems. Its ability to maintain performance under fluctuating conditions aligns well with modern energy management strategies, promoting efficiency and sustainability.

Moreover, the GE 164D2966P126 is characterized by its ease of integration into existing systems. It is designed to work with other components seamlessly, reducing installation time and costs. This compatibility is essential for industries that require rapid upgrades and scalability.

In conclusion, the GE 164D2966P126 represents a pinnacle of engineering innovation, embodying durability, efficiency, and advanced technology. Its robust features and exceptional characteristics make it ideal for applications in power generation and aerospace, ensuring that it meets the high standards expected in these critical sectors. With General Electric's commitment to excellence, the 164D2966P126 continues to support industries that depend on reliable performance and cutting-edge technology.
Top Page Image Contents