Manuals / Brands / Household Appliance / Sewing Machine / GE / Household Appliance / Sewing Machine

GE AF-300 General Information AF-300 Micro-$aver II , Drive Instructions

1 88

Download 88 pages, 874.19 Kb

i

These instructions do not purport to cover all details or variations in equipment, nor to provide for

every possible contingency to be met during installation, operation, and maintenance. Should

further information be desired or should particular problems arise that are not covered sufficiently for

the purchaser's purpose, the matter should be referred to GE Fuji Electric, Customer Service.

This document contains proprietary information of GE Fuji Electric and is furnished to its customers

solely to assist that customer in the installation, testing, and/or maintenance of the equipment

described. This document shall not be reproduced in whole or in part nor shall its contents be

disclosed to any third party without the written approval of GE Fuji Electric.

NOTE: The terms "inverter", "controller", and "drive" are sometimes used interchangeably through-

out the industry. We will use the term "Drive" in this document.

AF-300 Micro-Saver II™ and X$D™ are trademarks of General Electric Company. Energy Saver®

is a registered trademark of General Electric Company.

The terms "AF-300 Micro-Saver II" and AF-300M$II will be used interchangeably throughout this

document.

SHOCK HAZARD

labels may be located on or inside the Drive to alert people that dangerous

voltage may be present. (Refer to Section 1: Safety Precautions for Warnings and Cautions.)

Blank space has been intentionally left at the bottom of each page for the convenience of the user

in documenting notes.

WARNING: Always read the complete instructions

prior to applying power or troubleshooting the equipment

and follow all procedures step by step.

General Information – AF-300 Micro-$aver II

™

Drive Instructions

Contents

Main General Information AF-300 Micro-$aver II Drive Instructions i SHOCK HAZARD WARNING : TABLE OF CONTENTS Section Title Page TABLE OF CONTENTS (continued) iii Section Title Page DANGER, WARNING, CAUTION AND NOTE PARAGRAPHS WITHIN THIS INSTRUCTION MANUAL Section 1 SAFETY PRECAUTIONS WARNINGS HAZARD OF MOTOR OVERSPEED: MECHANICAL MOTION HAZARD : CAUTIONS UL/CSA Drive Caution Label ADVERTISSEMENT: CAUTION: ATTENTION: WARNING: AVERTISSEMENT: CAUTIONS (continued) II MODEL NO. SERIAL NO. INPUT: OUTPUT: (1) Keypad Part Names and Functions (2) Controlling Method for Keypad Panel WARNING - Drive Components 2-4 Output Power Supply Control TABLE 1: Standard Specifications Environmental Conditions Operation Control (continued) Operation (continued) ITEM SPECIFICATION 2-6 2-7 NOTE: Table 2: Drive Dimensions 240 Volt Single Phase 230 Volt Three Phase 480 Volt Three Phase Table 3: Drive Rating Efficiency and Watts Loss Table Dimensions Page Page Removing Top Cover Section 4 WIRING PROCEDURES Control Circuit Wiring CAUTION Main Circuit Wiring 240V Single Phase 1/4 to 3 HP 230 & 480V Three Phase 1/4 to 5 HP CAUTION: E (G) Table 4: Wire Size Recommendations & Circuit Protection Ratings 240V Single Phase and 230V Three Phase 480V Three Phase Page CAUTION: TABLE 5: Terminal Identification/Function Terminal Terminal Label Name Function TABLE 5: Terminal Identification/Function (continued) Terminal Terminal Label Name Function Drive Interface Details Section 5 DRIVE OPERATION PRE-OPERATION INSPECTION KEYPAD PANEL IDENTIFICATION / OPERATION FUNCTION CODE AND DATA CODE DESCRIPTION / SELECTION Keypad and Display Operation Programming Page Page Page 5-8 Summary of each operation mode : The following table shows a summary of the various modes. (F_02=0) Keys and Indicators Mode STOP Mode RUN Mode While Stopped While Running TRIP Mode Operation 5-10 TABLE 6: Function Codes Function Code Numbers Followed by Function Descriptions 5-11 TABLE 6: Function Codes (Cont'd) Function Code Numbers Followed by Function Descriptions Basic Functions 6-1 Section 6 FUNCTION CODE DESCRIPTIONS 6-2 6-3 6-4 * When set to 0.00 0.01 seconds. the time becomes 6-5 6-6 6-7 6-8 6-9 6-10 6-11 6-12 V 6-13 6-14 6-15 6-16 6-17 6-18 6-19 6-20 6-21 6-22 6-23 6-24 000 999 6-25 Page INSPECTION ITEMS CHART Item Inspection Criteria Corrective Action INSPECTION ITEMS MEASUREMENT POINTS AND METERS RECOMMENDED MEASUREMENT DEVICE CHART Item Simple Measurement Precision Measurement 8-1 Section 8 TROUBLESHOOTING TABLE 8: Fault Condition Description and Operation 8-2 TROUBLESHOOTING ( 1 ) Overcurrent O C 1 O C 2 O C 3 8-3 O U ( 2 ) Overvoltage 8-4 ( 3 ) Undervoltage 8-5 ( 4 ) Drive overheated ( 5 ) External alarm input Drive Overheating Drive Overload 8-6 ( 6 ) Overload Overload Protection Overload Protection of Drive Unit of Motor 8-7 ( 7 ) Memory error, keypad communications error, CPU error 8-8 ( 8 ) Drive output circuit error 8-9 ( 9 ) Motor will not run. 8-10 ( 10 ) Motor will run but speed will not change. 8-11 ( 11 ) Motor will stall during acceleration. 8-12 ( 12 ) Motor heating abnormal. WARRANTY PARTS AND SERVICE WARRANTY COVERAGE OUT-OF-WARRANTY PROCEDURES MOTORS Section 9 9-2 IN-WARRANTY FAILURE CHECKLIST AF-300 Micro-$aver II Spare Parts List Section 10 CE MARK Fig. 10-2 Recommended installation