GE AF-300 - page 18

3-3

Dimensions

Figure 4 Figure 5 Figure 6

Figure 7 Figure 8 Figure 9

Note: Inches (MM)

4.29 (109)

0.24 (6)

3.54 (90)

0.20 (5)

3.15 (80)

0.20 (5)

4.69 (119)

0.24 (6)

5.28 (134)

0.24 (6) 5.87 (149)

0.24 (6)

Contents

Main General Information AF-300 Micro-$aver II Drive Instructions i SHOCK HAZARD WARNING : TABLE OF CONTENTS Section Title Page TABLE OF CONTENTS (continued) iii Section Title Page DANGER, WARNING, CAUTION AND NOTE PARAGRAPHS WITHIN THIS INSTRUCTION MANUAL Section 1 SAFETY PRECAUTIONS WARNINGS HAZARD OF MOTOR OVERSPEED: MECHANICAL MOTION HAZARD : CAUTIONS UL/CSA Drive Caution Label ADVERTISSEMENT: CAUTION: ATTENTION: WARNING: AVERTISSEMENT: CAUTIONS (continued) II MODEL NO. SERIAL NO. INPUT: OUTPUT: (1) Keypad Part Names and Functions (2) Controlling Method for Keypad Panel WARNING - Drive Components 2-4 Output Power Supply Control TABLE 1: Standard Specifications Environmental Conditions Operation Control (continued) Operation (continued) ITEM SPECIFICATION 2-6 2-7 NOTE: Table 2: Drive Dimensions 240 Volt Single Phase 230 Volt Three Phase 480 Volt Three Phase Table 3: Drive Rating Efficiency and Watts Loss Table Dimensions Page Page Removing Top Cover Section 4 WIRING PROCEDURES Control Circuit Wiring CAUTION Main Circuit Wiring 240V Single Phase 1/4 to 3 HP 230 & 480V Three Phase 1/4 to 5 HP CAUTION: E (G) Table 4: Wire Size Recommendations & Circuit Protection Ratings 240V Single Phase and 230V Three Phase 480V Three Phase Page CAUTION: TABLE 5: Terminal Identification/Function Terminal Terminal Label Name Function TABLE 5: Terminal Identification/Function (continued) Terminal Terminal Label Name Function Drive Interface Details Section 5 DRIVE OPERATION PRE-OPERATION INSPECTION KEYPAD PANEL IDENTIFICATION / OPERATION FUNCTION CODE AND DATA CODE DESCRIPTION / SELECTION Keypad and Display Operation Programming Page Page Page 5-8 Summary of each operation mode : The following table shows a summary of the various modes. (F_02=0) Keys and Indicators Mode STOP Mode RUN Mode While Stopped While Running TRIP Mode Operation 5-10 TABLE 6: Function Codes Function Code Numbers Followed by Function Descriptions 5-11 TABLE 6: Function Codes (Cont'd) Function Code Numbers Followed by Function Descriptions Basic Functions 6-1 Section 6 FUNCTION CODE DESCRIPTIONS 6-2 6-3 6-4 * When set to 0.00 0.01 seconds. the time becomes 6-5 6-6 6-7 6-8 6-9 6-10 6-11 6-12 V 6-13 6-14 6-15 6-16 6-17 6-18 6-19 6-20 6-21 6-22 6-23 6-24 000 999 6-25 Page INSPECTION ITEMS CHART Item Inspection Criteria Corrective Action INSPECTION ITEMS MEASUREMENT POINTS AND METERS RECOMMENDED MEASUREMENT DEVICE CHART Item Simple Measurement Precision Measurement 8-1 Section 8 TROUBLESHOOTING TABLE 8: Fault Condition Description and Operation 8-2 TROUBLESHOOTING ( 1 ) Overcurrent O C 1 O C 2 O C 3 8-3 O U ( 2 ) Overvoltage 8-4 ( 3 ) Undervoltage 8-5 ( 4 ) Drive overheated ( 5 ) External alarm input Drive Overheating Drive Overload 8-6 ( 6 ) Overload Overload Protection Overload Protection of Drive Unit of Motor 8-7 ( 7 ) Memory error, keypad communications error, CPU error 8-8 ( 8 ) Drive output circuit error 8-9 ( 9 ) Motor will not run. 8-10 ( 10 ) Motor will run but speed will not change. 8-11 ( 11 ) Motor will stall during acceleration. 8-12 ( 12 ) Motor heating abnormal. WARRANTY PARTS AND SERVICE WARRANTY COVERAGE OUT-OF-WARRANTY PROCEDURES MOTORS Section 9 9-2 IN-WARRANTY FAILURE CHECKLIST AF-300 Micro-$aver II Spare Parts List Section 10 CE MARK Fig. 10-2 Recommended installation