Type (FVR _ _ _ |
| F12 |
| F25 | F50 | 001 |
| 002 |
| |
Applicable motor output1 | [Hp] | 1/8 |
| 1/4 | 1/2 | 1 |
| 2 |
| |
| Frequency setting |
| Key operation: |
| Setting with UP/DOWN keys | |||||
|
|
| Potentiometer: |
| Terminal for | |||||
|
|
| Analog signal: |
| ||||||
|
|
|
|
|
| |||||
| Display | Run mode | Output frequency is displayed. (3 digit LED) |
|
| |||||
|
| Fault mode | Cause of fault is displayed. |
|
|
|
| |||
|
| Other | LED comes on with charging voltage applied. |
|
| |||||
| Acceleration/Deceleration time |
| ||||||||
Control |
|
| time can be set independently. |
|
|
|
| |||
| Voltage frequency characteristics | Setting of maximum frequency/base frequency is variable. |
| |||||||
| Restart after momentary power failure | "Automatic restart" setting makes it possible to keep motor |
| |||||||
|
|
| running and restart drive in case of a momentary power failure. | |||||||
| High Limiter & Low Limiter |
| Upper limit and lower limit of frequency can be set. |
|
| |||||
| Bias setting |
| Bias setting is possible with respect to analog frequency setting. |
| ||||||
| Jump frequency |
| Three jump points and one jump width can be set. |
|
| |||||
| Torque boost |
| Setting variable in 32 steps. |
|
|
|
| |||
| Starting torque | [%] | 150% for 60 seconds. |
|
|
|
|
| ||
| Braking torque5 | [%] | 150% 1 min. | 100% 1 min. |
| 50% 1 min. | ||||
Braking | DC brake |
| Brake starting frequency: 3 Hz (fixed) |
|
| |||||
|
|
| Setting of braking current / braking time is variable. |
|
| |||||
| Overload |
| Detects overload current and stops drive. |
|
| |||||
| Momentary overcurrent |
| Protects drive In case of ground fault (detects at start) and |
| ||||||
|
|
| short circuit of output circuit. |
|
|
|
| |||
| Overvoltage |
| Detects overvoltage of DC bus and stops drive. |
|
| |||||
Protection | Overheating of cooling element | Detects abnormal temp. rise of cooling element and stops drive. |
| |||||||
| Motor protection |
| Protects standard |
| ||||||
|
|
| means of electronic thermal overload relay. |
|
| |||||
| Alarm protection |
| Outputs contact signal in case of a trip for protection |
| ||||||
|
|
| (1c contact capacity: AC250V 0.3A | cos = 0.3) |
|
| ||||
| Installation location |
| Indoor at an altitude of 3283 feet (1000m) or less and free of | |||||||
|
|
| dust, corrosive gas and oil mist. |
|
|
|
| |||
| Ambient temperature |
|
|
|
|
|
|
| ||
| Ambient humidity |
| 20 |
|
| |||||
Environment | Vibration |
| 19 feet/s2 (5.9m/s2) or less |
|
|
|
| |||
|
|
| Vibration frequency: 5 - 55 Hz |
|
|
|
| |||
| Storage temperature |
|
|
|
|
|
|
| ||
| Atmospheric pressure |
| Operation/storage: min 900 mb (equivalent to 3283 feet (1000m) |
| ||||||
|
|
| Transport: min 660 mb (equivalent to 10720 feet (3265m) | |||||||
| Enclosure |
| IP20 |
|
|
|
|
|
| |
Cooling method |
|
|
|
5) This indicates average braking torque of a single motor. (Value varies according to motor efficiency. | |
|
9