Consumer Support Troubleshooting Tips Installation Instructions Operating Instructions Safety Instructions

Installation instructions.

Important Installation Recommendations

Read entire manual. Failure to follow all guides and rules could cause personal injury or property damage.

BE SURE TO FOLLOW ALL APPLICABLE STATE AND LOCAL CODES.

Use a qualified installer.

Do not install the Reverse Osmosis system outside or in extreme hot or cold temperatures.

DO NOT INSTALL ON HOT WATER.

Recommended installation is under the sink. However, the unit can be installed in a remote location, up to 30 feet away from the sink. Additional installation materials may be required.

If Reverse Osmosis system is connected to a refrigerator icemaker, a special icemaker connection kit is required (RVKIT). Do not use copper tubing for the connection between the Reverse Osmosis system and the refrigerator.

Be sure the water supply conforms to the specifications; see the Specifications Guidelines section.

If water supply conditions are unknown, contact your municipal water company or your local health department for a list of contaminants in your area and a list of laboratories certified by your state to analyze drinking water.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. This system shall only be used for arsenic reduction on chlorinated water supplies containing detectable residual-free chlorine at the system inlet. Water systems using an in-line chlorinator should provide a one minute chlorine contact time before the RO system.This Reverse Osmosis system contains a replaceable treatment membrane cartridge critical for effective reduction of Total Dissolved Solids. The water should be tested periodically to verify that the system is performing satisfactorily. This system is acceptable for treatment of influent concentrations of no more than 27 mg/L nitrate and 3 mg/L nitrite in combination measured as N and is certified for nitrate/nitrite reduction only for water supplies with a pressure of 280kPa (40 psig) or greater.

Small parts remaining after the installation could be a choke hazard. Discard safely.

Tools and Materials Required for Installation

Battery Powered Cordless Drill

1/4″ Drill Bit

1-1/4″ Drill Bit (type as required) if mounting is needed for faucet

Adjustable Open-End Wrenches

Phillips and Straight Screwdrivers

Utility Knife

Contents Included with the Product:

Reverse Osmosis Assembly

Product Literature (Owner’s Manual and Installation, Use and Care Video, Performance Data Sheet and Owner Registration Card)

Water Supply Valve Parts Bag

Drain Line Adapter

27″ Length of 3/8″ Tubing

Storage Tank

Filter Replacement Reminder Label

Water Test Kit

INSTALLER RESPONSIBILITY: The water supply valve (see the Feed Water Supply section) is included for use in areas where codes permit. Installer must comply with state and/or local codes. If not, the installer must provide fittings to tap the cold water pipe for a feed water source to the Reverse Osmosis system (must adapt to 1/4″ OD tubing).

10

Page 10
Image 10
GE GXRV10ABL01 owner manual Installation instructions, Important Installation Recommendations

GXRV10ABL01 specifications

The GE GXRV10ABL01 is a sophisticated variable frequency drive (VFD) designed to enhance efficiency in various industrial applications. Characterized by its versatility and advanced technologies, this device is ideal for controlling the speed and torque of electric motors, making it an integral component for modern automation systems.

One of the most notable features of the GE GXRV10ABL01 is its compact design, which allows for easy integration into existing systems without requiring significant modifications. This space-saving characteristic makes it suitable for a range of environments, including manufacturing floors, processing plants, and HVAC systems.

The GXRV10ABL01 is equipped with cutting-edge control technologies that improve performance and energy efficiency. It utilizes advanced algorithms for precise motor control, enabling smooth acceleration and deceleration while minimizing energy consumption. This enhances the overall efficiency of processes such as pumping, fans, and conveyors.

Another key feature is its robust communication capabilities. The GXRV10ABL01 supports a variety of communication protocols, including Ethernet/IP, Modbus, and Profinet. This interoperability allows for seamless integration with other control systems and facilitates real-time monitoring and data exchange, supporting Industry 4.0 initiatives.

User-friendly programming and operation are facilitated by the drive's intuitive interface. The built-in keypad allows for straightforward configuration and adjustments, while the ability to connect to external displays enhances usability. Furthermore, the drive supports various programming options, enabling customization to meet specific application requirements.

Safety features are paramount in the design of the GE GXRV10ABL01. It comes equipped with built-in protection mechanisms, including overcurrent, overvoltage, and thermal overload protection. These safety measures help to prevent damage to both the drive and connected machinery, ensuring reliable operation and longevity.

Durability is another hallmark of the GXRV10ABL01. Its rugged construction and high-quality components make it resilient against harsh environments, withstanding fluctuations in temperature, dust, and moisture. This makes it a dependable choice for diverse industrial applications.

In summary, the GE GXRV10ABL01 is a state-of-the-art variable frequency drive that combines advanced control technologies, robust communication capabilities, and essential safety features. Its compact design, user-friendly interface, and durability ensure it meets the demands of modern industrial automation, providing greater efficiency and reliability for critical operations.