GRO~~G ~STRUCTIONS

This appliance must be grounded.

In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a power cord having a grounding wire with a grounding plug. The plug must be plu~ed into an outlet that is properly installed and grounded. (Fig. 1)

wARNING–Improper use of the grounding plug can result in a risk of electric shock.

PREFERRED

 

METHOD

 

 

QQ

 

%

 

Q

e“ o

+

@D

 

/’(

INSURE PROPER

 

GROUNO EXISTS

lg. 1

BEFORE USE

 

 

Consult a qualified electrician or service technician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

Where a standard two-prong wall receptacle is encountered, it is your personal responsibility and obligation to have it replaced with

aproperly grounded three-prong wall receptacle.

Do not under any circum- stice cut or remove the third @round) prong from the power cord.

Use of Adapter Plugs

Usage situations where apptiance’s power cord~ be disconnected infrequently.

Because of potential safety h-rds under certain conditions, we strongly recommend against the use of an adapter plug. However, if you still elect to use an adapter, where local codes permit, a

TEMPORARY CONNE~ION may be made to a properly grounded two-prong wall receptacle by the use of a U-L listed adapter (Fig. 2) which is available at most local hardware stores.

TEMPORARY METHOD

(ADAPTER PLUGS NOT PERMITTED IN CANAOA)

ALIGN LARGE

I

PRONGS/SLOTS ,/ m

II,.

~q

ee r’ ““ /

>INSURE PROPER

@—:j~~g~{:cTloN

@

Fig. 2

BEFORE USE

The larger slot in the adapter must be aligned with the larger slot in the wall receptacle to provide proper polarity in the connection of the power cord.

Caution: Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is meti, and not insulated, and the wall receptacle is grounded through the house wi~ing. You shoul~ have the circuit checked by a qualified electrician to make sure the receptacle is properly grounded.

When disconnecting the power cord from the adapter, always hold the adapter with one hand. If this is not done, the adapter ground terminal is very likely to break with repeated use. Should this happen, DO NOT USE the appliance until a proper ground has again been established.

Usage situations where apptiance’s power cord ~ be disconnected frequently.

Do not use an adapter plug

in these situations because disconnecting of the power cord places undue strain on the adapter and leads to eventual failure of the adapter ground terminal. You should have the two-prong wall receptacle replaced with a three- prong (grounding) receptacle by a qualified electrician before using the appliance,

Use of Extension Cords

Because of potential safety huards under certain conditions we strongly recommend against the use of an extension cord. However, if it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension cord shall be equal to or greater than the electrical rating of the appliance (15 amperes).

Such extension cords are obtainable through General Electric service.

If you do use an extension cord with your microwave+onvection oven, the interior light may flicker and the blower sound may vary when oven is in use. Cook and defrost times may be longer as well.

33

 

—-——

Page 33
Image 33
GE JET342G warranty Use of Adapter Plugs, Use of Extension Cords, Do not use an adapter plug

JET342G specifications

The GE JET342G is a sophisticated and innovative jet engine that exemplifies the latest advancements in aerospace technology. As part of GE Aviation's renowned product line, this engine is specifically designed for various commercial aircraft, combining high performance with groundbreaking efficiency.

One of the primary features of the JET342G is its exceptional thrust capabilities. With a thrust rating of approximately 34,000 pounds, it is engineered to provide robust performance during takeoff and ascent, while maintaining efficiency during cruise conditions. This powerful thrust enables it to operate effectively across a range of aircraft sizes, making it a versatile choice for airlines around the globe.

The engine incorporates state-of-the-art turbofan technology, which allows for lower fuel consumption and reduced emissions compared to older models. The JET342G's advanced materials, including lightweight composite fan blades and high-temperature superalloys, contribute to its durability and reliability. These materials enable the engine to withstand the rigors of flight, thereby extending its lifecycle and minimizing maintenance costs for operators.

Another standout characteristic of the JET342G is its advanced aerodynamics. The design features an optimized fan and high bypass ratio, which enhances the engine’s overall efficiency. These aerodynamic improvements help reduce drag and enhance the aircraft's performance, resulting in lower operational costs for airlines as fuel efficiency becomes increasingly crucial in a competitive market.

In addition to its performance specifications, the GE JET342G is equipped with sophisticated digital engine control systems. These systems utilize advanced algorithms and sensors to monitor engine performance in real-time, allowing for immediate adjustments to maintain optimal efficiency and safety. This level of monitoring enhances the reliability of the engine, providing operators with confidence in its performance over long distances.

Safety also remains a top priority within the design of the JET342G. The engine incorporates multiple redundancies and advanced diagnostic tools that enable early detection of potential issues, ensuring that any maintenance needs can be addressed promptly.

Overall, the GE JET342G is a remarkable achievement in jet engine technology. With its combination of power, efficiency, and advanced monitoring systems, it continues to set the standard for modern aviation engines, reinforcing GE Aviation's commitment to innovation and excellence in the aerospace industry. As airlines seek to strike a balance between performance and sustainability, the JET342G is poised to play a key role in the future of aviation.