Installation Instructions
STEP 11 POSITION AND LEVEL THE DISHWASHER
•Check to be sure the dishwasher is adjusted to correct height and is centered in the cutout.
•Open and close the door to insure proper operation of the door. If there is any binding or rubbing, readjust leveling legs.
Use a wrench to make adjustments.
•If the door rubs on the right side of the cabinet, extend the left rear leg by unscrewing it one quarter turn.
•If the door rubs against the left side of the cabinet, extend the right rear leg by unscrewing it one quarter turn.
•Check level again. Repeat the procedure if necessary.
Door Rub | Door Rub |
On Right | On Left |
Hand Side Hand Side | |
Adjust | Adjust |
This | This |
Leg | Leg |
U | U |
NSCREW | NSCREW |
STEP 12 PRE-TEST CHECK LIST
Installation service calls are not covered by your warranty. To avoid unnecessary charges, review this list carefully.
♦Check to be sure power is OFF.
♦Open the door and remove all foam and paper packaging.
♦Pull lower rack out, about half way. Check to be sure it does not roll back or forwards on the door. If the rack moves, adjust leveling legs.
♦Verify water supply and drain lines are not kinked or in contact with other components.
♦Turn on the sink hot water faucet and verify water temperature. Incoming water temperature must be between 120°F and 150°F. 120°F min. temperature is required for best wash performance.
♦Turn on water supply.
♦Open the door. Check to be sure Insulation Board does not interfere with door opening.
|
|
| CHECK WATER FILL LEVEL |
|
| |
| STEP 13 | DISHWASHER WET TEST |
|
| ||
| For best performance, check the water fill level. | |||||
|
|
| ||||
| ♦ Turn on power supply. | Run through a complete RINSE ONLY cycle to ensure it is emptying | ||||
| ♦ Select the normal cycle and press the start button. | and filling correctly. For low water pressure situations run the | ||||
| ♦ The control will indicate a slow/no fill by flashing the CHINA | RINSE ONLY cycle 3 times. | ||||
| CRYSTAL, LIGHT WASH OR WASH CYCLE light. Check water | cycle, pause the dishwasher and check the water level inside the | ||||
| supply, then adjust fill time according to the chart shown. | dishwasher. If the water level is not above the minimum water level | ||||
| ♦ Check to be sure that water enters the dishwasher, wait up to | (marked on the lower spray support tower), increase the fill level. | ||||
| 2 minutes. If water does not enter the dishwasher, check to be | 1. Ensure the dishwasher is not running through a cycle. Depress | ||||
| sure that water is turned on. | the WATER TEMP button for 10 seconds until the second buzzer | ||||
| ♦ Check for leaks under the dishwasher. If a leak is found, turn | sounds (except on ZBD6600). |
|
| ||
| power and water off, then tighten connections. Restore power | 2. Press the START/CANCEL button to select fill time, as per chart | ||||
| and water supply. | (65 seconds is the factory setting). |
|
| ||
| ♦ Check for leaks around the door. A leak around the door could be | 3. To test time, press DELAY START. The dishwasher will start filling. | ||||
| caused by door rubbing or hitting against adjacent cabinetry. | Listen for the dishwasher to complete filling. Once filled, the fill | ||||
| Reposition the dishwasher if necessary. | level must be checked to ensure fill time is correct. | ||||
| ♦ After the dishwasher drains check drain lines. If leaks are found, | 4. Once complete, press the WATER TEMP button to exit fill time | ||||
| turn power off, correct as necessary. | mode. |
|
| ||
| ♦ The control will indicate a slow/no drain by flashing the RINSE |
| Continue to press the START/CANCEL button | |||
| ONLY, SANI WASH or HEAT OPTIONS. Check that the airgap is |
| until the desired indicator is illuminated. | |||
| clear of debris and that the knockout in the disposer or waste tee |
| Cycle Statue Indicators | Fill Time |
| |
| is fully removed. Check that the drain hose is not kinked. |
| SENSING | 60 seconds | ||
| ♦ Open the dishwasher door and make sure that most of the water |
|
|
|
| |
|
| WASHING | 65 seconds |
| ||
| has drained. If not, check that disposer plug has been removed |
| ||||
|
| RINSING | 70 seconds |
| ||
| and that air gap is not plugged. |
| ||||
|
| DRYING | 80 seconds |
| ||
| ♦ Cancel the dishwasher cycle and complete the installation. |
| ||||
| ♦ Remove protective film if present from the control panel and door. |
| CLEAN | 90 seconds | ||
|
|
|
|
|
|
|
13