Manuals / GE / Kitchen Appliance / Convection Oven

GE SCB 1001 manual Components, Component Access Chart, Serviceability, InstalledPartiallyRemoved

Models: SCB 1000 SCB 1001 ZSC 1000 ZSC 1001

1 46

Download 46 pages 13.99 Kb

Page 22

Image 22

Components

Component Access Chart

WARNING:

•The oven is heavy and requires two people to remove from the cabinet or wall opening. Care should be taken when removing and installing.

•Sharp edges may be exposed when servicing. Use caution to avoid injury. Wear Kevlar gloves or equivalent protection.

Serviceability

- - - UnitUnitUnit

InstalledPartiallyRemoved

Removed

Blower Assembly

Capacitor and Diode

Cavity Light

Cavity TCO

Control Panel Assembly

Convection Fan Motor

Convection Heater Assembly

Damper Assembly

Door

Door Assembly

Fuse

High Voltage Transformer

Humidity Sensor

Left and Right Door Switch Assemblies

Lower Heater Assembly

Low Voltage Transformer

Magnetron and Magnetron Thermostat

Noise Filter

Thermistor

Turntable Motor

Turntable Support

Upper Heater Assembly

Upper Heater TCO

– 22 –

Page 22

Image 22

GE SCB 1001, ZSC 1001, ZSC 1000 Components, Component Access Chart, Serviceability, InstalledPartiallyRemoved, UnitUnitUnit

Contents

SCB SCB ZSC ZSC Technical Service GuideAdvantium GE Consumer & IndustrialTechnical Service Guide Copyright IMPORTANT SAFETY NOTICERECONNECT ALL GROUNDING DEVICES GE Consumer & Industrial3. SEAL AND SEALING SURFACES ARCING, WEAR AND OTHER DAMAGE A. DO NOT OPERATE OR ALLOW THE OVEN TO BE OPERATED WITH THE DOOR OPEN1. INTERLOCK OPERATION 2. PROPER DOOR CLOSING 4. DAMAGE TO OR LOOSENING OF HINGES AND LATCHESTable of Contents Model Number NomenclatureS C B 1 0 0 0 D B B Serial NumberIntroduction Features and BeneﬁtsContinued Next Page Turntable FAN MSG REM MUTE TIMERWire Oven Rack and Aluminum Baking Sheet Non-stick Metal TrayControl Features Continued Next PageLights Cooking TimesFan/Vent Oven HeatRear Convection Heat Element Speed Cook SystemHalogen Lamp and Ceramic Heaters MicrowaveLower Heater Speedcook Power LevelsUpper Heaters Microwave EnergyVoltage Voltage Compensation ChartThermal Compensation Chart Thermal ProtectionLower Power Upper HeaterUpper Power Lower HeaterElectrical Requirements InstallationAdvance Planning Single Advantium 120 InstallationMain Component Locator View Component Locator ViewsFront View Control Panel Assembly Convection Fan Assembly TurntableHigh Voltage Transformer Diode Upper Heater Assembly Capacitor Top ViewBottom View Blower AssemblyControl Panel Assembly Low Voltage Transformer Humidity Sensor Left Side ViewRight Side View Oven Cavity TCO Lower Heater AssemblyControl Panel Control Panel Assembly Shown separatedPower Board Selector BoardContinued next page Control Boards and Panel ConnectionsPower Board CN11 CN4Control Board Relay BoardContinued next page Selector Board 20-Pin Connector to CN10 on Control BoardDisplay Board Control PanelServiceability Component Access ChartComponents InstalledPartiallyRemovedAccess Cover Oven Removal / Partial RemovalOuter Cover Door Removal Door AssemblyDoor-Removal Position To disassemble the doorTo remove the control panel assembly Control Panel AssemblyContinued Next Page To remove the relay board To remove the power boardContinued Next Page To remove the display board To remove the control panel bracketTo remove the control board Continued Next PageTo remove the control panel Low Voltage TransformerTo remove the selector board Resistance CheckCavity Light FuseNoise Filter Capacitor and DiodeHigh Voltage Transformer Magnetron and Magnetron TCOMagnetron TCO Damper Door Switch Damper AssemblyBlower Assembly SwitchUpper Heater and Oven Cavity TCOs Upper Heater Assembly To remove the upper heater assemblyThermistor Lower Heater AssemblyConvection Heater Assembly and Thermistor To remove the lower heater assemblyConvection Heater Element Convection Fan MotorTurntable Motor Humidity SensorHumidity Sensor Test How to Test the Monitor Switch Left and Right Door Switch AssembliesHow to Test Primary Interlock and Door Sensing Switches How to Test Interlock SystemTo replace the door switches Rotate SwitchHow to Adjust the Interlocks Continued Next PageNote Each latch board is held in place with 2 Phillips-head screws. The screws are recessed from the top of the outer cover. Access holes are provided. A magnetic screwdriver is necessary to capture these screws Diagnostics and Service Information USE ONLY HEAT AND MICROWAVE RESISTIVE GLASS BOWLStandard Test Load Fault CodesDemo Mode DisplayProof Feature Microwave Leak TestWARNING POWER MUST BE DISCONNECTED BEFORE SERVICING THIS APPLIANCE Schematics and Wiring DiagramsContinued Next Page Page GE Will Replace WarrantyFor The Period Of What GE Will Not Cover