Manuals / GE / Kitchen Appliance / Convection Oven

GE ZSC 1001, ZSC 1000, SCB 1001, SCB 1000 manual Convection Heater Element, Convection Fan Motor

Models: SCB 1000 SCB 1001 ZSC 1000 ZSC 1001

1 46

Download 46 pages 13.99 Kb

Page 36

Convection Heater Element

Convection Heater Element

The convection heater assembly is held in place by two 7-mm hex-nuts and 4 Phillips-head screws The convection heater element has an approximate resistance value of 9.5 Ω. Two Phillips-head screws connect the power wires to the element terminals.

Convection Fan Motor

The convection fan motor wire leads have locking tabs that must be depressed to be disconnected. To remove each wire from the fan motor, depress the clip using a small blade screwdriver and pull the wire off the terminal as shown.

The convection heater element is held in place by 4 Phillips-head screws. (Three screws on the front, and 1 screw on the end.)

End View of Element

ELECTRICAL TERMINAL

RELEASE/LOCKING TAB

The outer convection fan must be removed before removing the motor. The outer convection fan is held in place by a 7-mm nut, lockwasher, spacer and ﬂat washer.

Front View of Outer Convection Fan

The convection fan motor is held in place by 3 Phillips-head screws .

Rear View of Convection Fan

Convection Fan Motor

– 36 –

Image 36

GE ZSC 1001, ZSC 1000, SCB 1001, SCB 1000 manual Convection Heater Element, Convection Fan Motor

Contents

Technical Service Guide AdvantiumSCB SCB ZSC ZSC GE Consumer & IndustrialIMPORTANT SAFETY NOTICE RECONNECT ALL GROUNDING DEVICESTechnical Service Guide Copyright GE Consumer & IndustrialA. DO NOT OPERATE OR ALLOW THE OVEN TO BE OPERATED WITH THE DOOR OPEN 1. INTERLOCK OPERATION 2. PROPER DOOR CLOSING3. SEAL AND SEALING SURFACES ARCING, WEAR AND OTHER DAMAGE 4. DAMAGE TO OR LOOSENING OF HINGES AND LATCHESTable of Contents Nomenclature S C B 1 0 0 0 D B BModel Number Serial NumberFeatures and Beneﬁts IntroductionContinued Next Page FAN MSG REM MUTE TIMER Wire Oven Rack and Aluminum Baking SheetTurntable Non-stick Metal TrayControl Features Continued Next PageCooking Times Fan/VentLights Oven HeatSpeed Cook System Halogen Lamp and Ceramic HeatersRear Convection Heat Element MicrowaveSpeedcook Power Levels Upper HeatersLower Heater Microwave EnergyVoltage Compensation Chart Thermal Compensation ChartVoltage Thermal ProtectionUpper Heater Upper PowerLower Power Lower HeaterInstallation Advance PlanningElectrical Requirements Single Advantium 120 InstallationComponent Locator Views Front ViewMain Component Locator View Control Panel Assembly Convection Fan Assembly TurntableTop View Bottom ViewHigh Voltage Transformer Diode Upper Heater Assembly Capacitor Blower AssemblyLeft Side View Right Side ViewControl Panel Assembly Low Voltage Transformer Humidity Sensor Oven Cavity TCO Lower Heater AssemblyControl Panel Assembly Shown separated Power BoardControl Panel Selector BoardControl Boards and Panel Connections Power BoardContinued next page CN11 CN4Relay Board Control BoardContinued next page 20-Pin Connector to CN10 on Control Board Display BoardSelector Board Control PanelComponent Access Chart ComponentsServiceability InstalledPartiallyRemovedOven Removal / Partial Removal Access CoverOuter Cover Door Assembly Door-Removal PositionDoor Removal To disassemble the doorControl Panel Assembly To remove the control panel assemblyContinued Next Page To remove the power board To remove the relay boardContinued Next Page To remove the control panel bracket To remove the control boardTo remove the display board Continued Next PageLow Voltage Transformer To remove the selector boardTo remove the control panel Resistance CheckCavity Light FuseNoise Filter Capacitor and DiodeMagnetron and Magnetron TCO High Voltage TransformerMagnetron TCO Damper Assembly Blower AssemblyDamper Door Switch SwitchUpper Heater and Oven Cavity TCOs Upper Heater Assembly To remove the upper heater assemblyLower Heater Assembly Convection Heater Assembly and ThermistorThermistor To remove the lower heater assemblyConvection Heater Element Convection Fan MotorHumidity Sensor Turntable MotorHumidity Sensor Test Left and Right Door Switch Assemblies How to Test Primary Interlock and Door Sensing SwitchesHow to Test the Monitor Switch How to Test Interlock SystemRotate Switch How to Adjust the InterlocksTo replace the door switches Continued Next PageNote Each latch board is held in place with 2 Phillips-head screws. The screws are recessed from the top of the outer cover. Access holes are provided. A magnetic screwdriver is necessary to capture these screws Diagnostics and Service Information USE ONLY HEAT AND MICROWAVE RESISTIVE GLASS BOWLFault Codes Demo ModeStandard Test Load DisplayProof Feature Microwave Leak TestSchematics and Wiring Diagrams WARNING POWER MUST BE DISCONNECTED BEFORE SERVICING THIS APPLIANCEContinued Next Page Page Warranty For The Period OfGE Will Replace What GE Will Not Cover