Manuals / GE / Kitchen Appliance / Convection Oven

GE ZSC 1000, ZSC 1001, SCB 1001, SCB 1000 manual Cavity Light, Fuse

Models: SCB 1000 SCB 1001 ZSC 1000 ZSC 1001

1 46

Download 46 pages 13.99 Kb

Page 29

Cavity Light

Cavity Light		Fuse

The oven lamp is inserted in a socket that is attached to the lamp housing with 2 Phillips-head screws. The screws are recessed from the top of the outer cover. Access holes are provided. A magnetic screwdriver is necessary to capture these screws.

It is necessary to remove the control panel to access the oven lamp. (See Control Panel Assembly.)

The oven cavity light will come on during a microwave cooking cycle.

Important Note: The primary interlock, monitor interlock, door sensing (secondary interlock) switches, and the relay board must all be replaced when the 20 amp fuse opens due to operation of the monitor interlock switch.

The unit is equipped with a 20 amp fuse (Part # WB27X10388).

The fuse is located in a receptacle near the top of the noise ﬁlter and is common to all functions and door switches.

Fuse

Note: If the fuse opens, it will disable all oven functions including the display. The oven must be partially removed to access the fuse. (See Oven

Removal / Partial Removal.)

Caution: Do not twist the lamp.

The oven lamp is a 130-VAC, 20-watt lamp (Part #

WB08X10050). It is a plug-in type lamp.

– 29 –

Image 29

GE ZSC 1000, ZSC 1001, SCB 1001, SCB 1000 manual Cavity Light, Fuse

Contents

Advantium Technical Service GuideSCB SCB ZSC ZSC GE Consumer & IndustrialRECONNECT ALL GROUNDING DEVICES IMPORTANT SAFETY NOTICETechnical Service Guide Copyright GE Consumer & Industrial1. INTERLOCK OPERATION 2. PROPER DOOR CLOSING A. DO NOT OPERATE OR ALLOW THE OVEN TO BE OPERATED WITH THE DOOR OPEN3. SEAL AND SEALING SURFACES ARCING, WEAR AND OTHER DAMAGE 4. DAMAGE TO OR LOOSENING OF HINGES AND LATCHESTable of Contents S C B 1 0 0 0 D B B NomenclatureModel Number Serial NumberContinued Next Page Features and BeneﬁtsIntroduction Wire Oven Rack and Aluminum Baking Sheet FAN MSG REM MUTE TIMERTurntable Non-stick Metal TrayContinued Next Page Control FeaturesFan/Vent Cooking TimesLights Oven HeatHalogen Lamp and Ceramic Heaters Speed Cook SystemRear Convection Heat Element MicrowaveUpper Heaters Speedcook Power LevelsLower Heater Microwave EnergyThermal Compensation Chart Voltage Compensation ChartVoltage Thermal ProtectionUpper Power Upper HeaterLower Power Lower HeaterAdvance Planning InstallationElectrical Requirements Single Advantium 120 InstallationFront View Component Locator ViewsMain Component Locator View Control Panel Assembly Convection Fan Assembly TurntableBottom View Top ViewHigh Voltage Transformer Diode Upper Heater Assembly Capacitor Blower AssemblyRight Side View Left Side ViewControl Panel Assembly Low Voltage Transformer Humidity Sensor Oven Cavity TCO Lower Heater AssemblyPower Board Control Panel Assembly Shown separatedControl Panel Selector BoardPower Board Control Boards and Panel ConnectionsContinued next page CN11 CN4Continued next page Relay BoardControl Board Display Board 20-Pin Connector to CN10 on Control BoardSelector Board Control PanelComponents Component Access ChartServiceability InstalledPartiallyRemovedOuter Cover Oven Removal / Partial RemovalAccess Cover Door-Removal Position Door AssemblyDoor Removal To disassemble the doorContinued Next Page Control Panel AssemblyTo remove the control panel assembly Continued Next Page To remove the power boardTo remove the relay board To remove the control board To remove the control panel bracketTo remove the display board Continued Next PageTo remove the selector board Low Voltage TransformerTo remove the control panel Resistance CheckFuse Cavity LightCapacitor and Diode Noise FilterMagnetron TCO Magnetron and Magnetron TCOHigh Voltage Transformer Blower Assembly Damper AssemblyDamper Door Switch SwitchUpper Heater and Oven Cavity TCOs To remove the upper heater assembly Upper Heater AssemblyConvection Heater Assembly and Thermistor Lower Heater AssemblyThermistor To remove the lower heater assemblyConvection Fan Motor Convection Heater ElementHumidity Sensor Test Humidity SensorTurntable Motor How to Test Primary Interlock and Door Sensing Switches Left and Right Door Switch AssembliesHow to Test the Monitor Switch How to Test Interlock SystemHow to Adjust the Interlocks Rotate SwitchTo replace the door switches Continued Next PageNote Each latch board is held in place with 2 Phillips-head screws. The screws are recessed from the top of the outer cover. Access holes are provided. A magnetic screwdriver is necessary to capture these screws USE ONLY HEAT AND MICROWAVE RESISTIVE GLASS BOWL Diagnostics and Service InformationDemo Mode Fault CodesStandard Test Load DisplayMicrowave Leak Test Proof FeatureContinued Next Page Schematics and Wiring DiagramsWARNING POWER MUST BE DISCONNECTED BEFORE SERVICING THIS APPLIANCE Page For The Period Of WarrantyGE Will Replace What GE Will Not Cover