SATA-II 2 Secondary RAID, Serial-ATAII | Gigabyte GA-K8N51PVM9-RH

SATA-II 2 Primary RAID

Enabled	Enable SATAII 2 1st SATA RAID function.
Disabled	Disable this function. (Default value)
SATA-II 2 Secondary RAID
Enabled	Enable SATAII 2 2nd SATA RAID function.
Disabled	Disable this function. (Default value)
On-Chip IDE Channel0
Enabled	Enable onboard 1st channel IDE port. (Default value)
Disabled	Disable onboard 1st channel IDE port.
On-Chip IDE Channel1
Enabled	Enable onboard 2nd channel IDE port. (Default value)
Disabled	Disable onboard 2nd channel IDE port.
IDE1 Conductor Cable
Auto	BIOS autodetects IDE1 conductor cable .(Default Value)

ATA66/100/133 Set IDE1 Conductor Cable to ATA66/100/133 (Please make sure your IDE

	device and cable are compatible with ATA66/100/133).
ATA33	Set IDE1 Conductor Cable to ATA33. (Please make sure your IDE device
	and cable are compatible with ATA33)

IDE2 Conductor Cable

Auto BIOS autodetects IDE2 conductor cable. (Default Value)

ATA66/100/133 Set IDE2 Conductor Cable to ATA66/100/133. (Please make sure your IDE

	device and cable are compatible with ATA66/100/133)
ATA33	Set IDE2 Conductor Cable to ATA33. (Please make sure your IDE device
	and cable are compatible with ATA33)

Serial-ATAII 1

Enabled	Enable Serial-ATAII 1 support. (Default Value)
Disabled	Disable Serial-ATAII 1 support.

Serial-ATAII 2

Enabled	Enable Serial-ATAII 2 support. (Default Value)
Disabled	Disable Serial-ATAII 2 support.

On-Chip USB

V1.1+V2.0	Enable USB 1.1 and USB 2.0 controllers. (Default Value)
V1.1	Enable only USB 1.1 controller
Disabled	Disable onchip USB support.

USB Keyboard Support

Enabled	Enable USB keyboard support.
Disabled	Disable USB keyboard support. (Default value)

USB Mouse Support

Enabled	Enable USB mouse support.
Disabled	Disable USB mouse support. (Default value)

English

- 37 -

BIOS Setup

Image 37

Gigabyte GA-K8N51PVM9-RH SATA-II 2 Secondary RAID, On-Chip IDE Channel0, On-Chip IDE Channel1, IDE1 Conductor Cable

Contents

GA-K8N51PVM9-RH-NV Motherboard Product Manual Classification Copyright Table of Contents Drivers Installation Optional Accessories GA-K8N51PVM9-RH-NV Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your Computer Feature Summary 4M bit flash ROM Installation of the CPU Installation of the CPU and CPU Cooler Installation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power Connector IDE1 / IDE2 IDE Connector Pwrled Fpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel Connector Tpmclr Tpmphysicalpresence USB1 / FUSB2 Front USB Connector Spdifio Spdif In/Out Coma Coma Connector CI Chassis Intrusion, Case Open Clrcmos Clear Cmos English Main Menu Status Page Setup Menu / Option Page Setup Menu F12 Boot Menu Main Menu For example Bios Ver. F3d „ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI Configuration Time Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave IDE Channel 2/3/4/5 Master Drive a Floppy 3 Mode Support for Japan AreaMemory Base Memory Hard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Boot Up Floppy Seek Init Display First Password CheckFrame Buffer Size Onboard GPU SPP Integrated Peripherals On-Chip IDE Channel0 SATA-II 2 Secondary RAIDOn-Chip IDE Channel1 IDE1 Conductor Cable Parallel Port Mode Onboard LAN Boot ROMOnboard Audio Function Onboard LAN Function Power-On by Alarm Power Management SetupPME Event Wake Up Modem Ring On KB Power on Password Power On By KeyboardPower On By Mouse AC Back Function PCI 1 IRQ Assignment PnP/PCI Configurations PC Health Status System Smart FAN Control CPU Smart FAN Control Note CPU Frequency Frequency/Voltage ControlPcie Clock K8 CPU Clock Ratio TPM Control Trusted Platform Module Control Security Chip Configuration Load Optimized Defaults Load Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit Setup Install Chipset Drivers Drivers Installation Software Information Software Application Contact Us Hardware Information Dual-Monitor Setup Horizontal Span Mode Clone ModeVertical Span Mode Dual View Mode English EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utility Steps Using the Q-FlashTMutility You can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screen Congratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM Utility English Installing Sata hard drives in your computer SPP Nvidia Mirror Step Save and exit Bios Setup GA-K8N51PVM9-RH-NV Motherboard Configuring RAID set in RAID Bios YES Nvidia Making a Sata Driver Disk Cd bootdrv Menu Installing Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Solutions Configuring a bootable RAID array with Microsoft Windows 1NO .0.M GA-K8N51PVM9-RH-NV Motherboard English Stereo Speakers Connection and Settings5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English English Sound Effect Configuration Introduction of the TPM Security Solution Troubleshooting English English English English English English English Taiwan Headquarters Contact Us Gigabyte Global Service System