On-Chip Primary IDE, On-Chip Secondary IDE | Gigabyte GA-K8U-939

English

On-Chip Primary IDE

Enabled	Enable onboard 1st channel IDE port. (Default value)
Disabled	Disable onboard 1st channel IDE port.

On-Chip Secondary IDE

Enabled	Enable onboard 2nd channel IDE port. (Default value)
Disabled	Disable onboard 2nd channel IDE port.

IDE DMA transfer access

Enabled	Enable IDE DMA transfer access. (Default value)
Disabled	Disable this function.

Onboard H/W LAN

Enabled	Enable onboard H/W LAN function. (Default value)
Disabled	Disable this function.

USB 1.1 Controller

Enabled	Enable USB 1.1 controller. (Default value)
Disabled	Disable USB 1.1 controller.

USB Keyboard Support

Enabled	Enable USB keyboard support.
Disabled	Disable USB keyboard support. (Default value)

USB Mouse Support

Enabled	Enable USB mouse support.
Disabled	Disable USB mouse support. (Default value)

USB 2.0 Controller

You can disable this function if you are not using onboard USB 2.0 feature.

Enabled	Enable USB 2.0 controller. (Default value)
Disabled	Disable USB 2.0 controller.

OnBoard LAN Boot ROM

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Disabled	Disable this function. (Default value)
Enabled	Enable this function.

Onboard Serial Port 1

Auto	BIOS will automatically setup the port 1 address.
3F8/IRQ4	Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
2F8/IRQ3	Enable onboard Serial port 1 and address is 2F8/IRQ3.
3E8/IRQ4	Enable onboard Serial port 1 and address is 3E8/IRQ4.
2E8/IRQ3	Enable onboard Serial port 1 and address is 2E8/IRQ3.
Disabled	Disable onboard Serial port 1.

Onboard Serial Port 2


Auto	BIOS will automatically setup the port 1 address.
3F8/IRQ4	Enable onboard Serial port 2 and address is 3F8/IRQ4.
2F8/IRQ3	Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)
3E8/IRQ4	Enable onboard Serial port 2 and address is 3E8/IRQ4.
2E8/IRQ3	Enable onboard Serial port 2 and address is 2E8/IRQ3.
Disabled	Disable onboard Serial port 2.

GA-K8U-939 Motherboard		- 36 -

Image 36

Gigabyte GA-K8U-939 user manual On-Chip Primary IDE, On-Chip Secondary IDE, IDE DMA transfer access, Onboard H/W LAN

Contents

GA-K8U-939 Motherboard Copyright Product Manual Classification Table of Contents Drivers Installation GA-K8U-939 Motherboard Layout 939 Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your Computer Feature Summary CPU Installation of the CPU and Heatsink Installation of the CPU Installation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector FDD FDD Connector IDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA Connector BAT Battery Pwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In Connector Surcen Surround Center Connector Spdifio Spdif In / Out Connector USB1 / FUSB2 Front USB Connector 17 IR Game Game Connector Clrcmos Clear Cmos English English Status Page Setup Menu / Option Page Setup Menu Main Menu Main Menu For example GA-K8U-939 / Bios Ver. F1 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit Setup Standard Cmos Features Time Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on Memory Advanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password Check OnChip Sata Mode Integrated PeripheralsOnChip Audio OnChip Sata IDE DMA transfer access OnBoard LAN Boot ROMOn-Chip Primary IDE On-Chip Secondary IDE Uart Mode Select UR2 Duplex ModeParallel Port Mode Onboard Parallel port Power Management Setup PME Event Wake UpModem Ring Resume Resume by Alarm Power on Function PnP/PCI Configurations PCI 1 IRQ Assignment Current CPU/System Temperature PC Health StatusCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPM Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving English Drivers Installation Install Chipset Drivers Software Application Software Information Hardware Information Contact Us English Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and Restart Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utility Using the Q-FlashTMutility Steps You can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen Congratulation!! You have updated Bios successfully Bios file becomes F4 after updating Method 2 @BIOSTM Utility Methods and steps English Serial ATA Bios Setting Utility Introduction RAID Levels Configuring the ALi RAID Bios Entering the RAID Bios Setup Create RAID 0 Striping for Performance Main Menu English Create RAID 1 Mirroring for Reliability Create Jbod for integrated Capacity Delete RAID Settings & Partition Delete All RAID Settings & PartitionRebuild RAID Array Installing the RAID drivers Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English English English Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing and UAJ IntroductionAuto-detecting Manual setting Enable UAJ functionUAJ Introduction Troubleshooting English English English English English English Contact Us Taiwan Headquarters China Shanghai