2. | Attach a Wheel (96) to the Base (95) with a 3/8" | 2 |
|
|
|
|
|
|
| x 2" Bolt (5) and a 3/8" Nut (9). Do not over- |
|
|
|
|
|
| |
| tighten the Nut; the Wheel must turn freely. |
|
|
|
|
|
|
|
| See the inset drawing. Cut the plastic tie near |
|
| 95 |
|
|
|
|
| the Upright Wire (97). |
| 5 |
|
|
|
| |
|
|
|
|
|
|
|
| |
|
|
|
| 9 | 96 | 97Cut |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |
3. Identify the Right Upright (86) and the Right | 3 |
|
|
|
|
|
| |
| Upright Spacer (92). |
|
|
| 86 |
|
|
|
| Insert the Upright Wire (97) through the Right |
|
|
|
|
|
| |
| Upright Spacer (92) as shown. Then, set the |
|
|
|
|
|
|
|
| Right Upright Spacer on the Base (95). Be care- |
| 97 |
|
|
|
| |
| ful not to pinch the Upright Wire. | Wire Tie |
|
| 97 |
| ||
| Have a second person hold the Right Upright |
|
|
|
| 92 | ||
|
|
|
|
|
| |||
| (86) near the Base (95). See the inset drawing. |
|
|
|
|
|
| |
| Tie the wire tie in the Right Upright securely |
|
|
|
|
| 95 | |
| around the end of the Upright Wire (97). Then, |
|
|
|
|
| ||
| pull the other end of the wire tie until the Upright |
|
|
|
|
|
|
|
| Wire is routed completely through the Right |
|
|
|
|
|
|
|
| Upright. | 97 |
| 86 |
|
|
|
|
|
|
| Wire |
|
|
|
| |
|
|
|
| Tie |
|
|
|
|
4. Hold a Bolt Spacer (25) inside the lower end of | 4 |
|
|
|
|
|
| |
| the Right Upright (86). Next, insert a 3/8" x 4 |
|
|
|
|
|
| |
| 1/2" Bolt (6) with a 3/8" Star Washer (10) into |
| 86 |
| 6 |
|
| |
| the Right Upright and the Bolt Spacer. Repeat |
| 92 |
|
| |||
| this step with a second Bolt Spacer (25), 3/8" |
|
|
|
|
|
| |
| x 4 1/2" Bolt (6), and 3/8" Star Washer (10). |
|
|
|
| 10 |
|
|
| Then, set the Right Upright in the Right Upright |
|
|
|
|
|
| |
| Spacer (92). Be careful not to pinch the |
|
|
|
|
|
|
|
| Upright Wire (97). |
|
|
|
|
| 25 |
|
| Partially tighten the 3/8" x 4 1/2" Bolts (6); do |
|
|
|
| 97 |
| |
|
|
|
|
|
|
| ||
| not fully tighten the Bolts yet. |
|
|
|
|
|
| |
|
| 7 |
|
|
|
|
|
|
