HandyTone-386 User ManualGrandstream Networks, Inc.

 

Firmware Key:

 

 

 

 

 

 

 

 

 

 

(in Hexadecimal Representation)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Onhook Threshold:

 

 

800 ms

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FXS Impedance:

 

 

600 Ohm (North America)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Caller ID Scheme:

 

 

Bellcore (North America)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Onhook Voltage:

 

 

36V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Polarity Reversal:

 

 

 

No

 

 

Yes (reverse polarity upon call establishment and

 

 

 

termination)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NTP Server:

Syslog Server:

time.nist.gov

(URI or IP address)

 

Syslog Level:

NONE

Update

All Rights Reserved Grandstream Networks, Inc. 2005

Admin Password

Administrator password. Only administrator can configure the “Advanced Settings” page. Password field is purposely blanked for security reason after clicking update and saved. The maximum password length is 25 characters.

 

Home NPA

 

Local area code for North American Dial Plan.

 

 

 

 

 

 

 

 

 

 

 

 

Layer 3 QoS

 

This field defines the layer 3 QoS parameter which can be the value used for

 

 

 

 

IP Precedence or Diff-Serv or MPLS. Default value is 48.

 

 

 

 

 

 

 

 

 

 

 

 

Layer 2 QoS

 

Layer 2 QoS settings. Default setting is blank. Other VLAN supported

 

 

 

 

equipments required if configured these settings.

 

 

 

 

 

 

 

 

 

 

 

 

No Key Entry

 

Default is 4 seconds. User can short or extend that depends on digits dialed

 

 

timeout

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STUN Server

 

IP address or Domain name of the STUN server.

 

 

 

 

 

 

 

 

 

 

 

 

Keep-alive interval

 

Default is 20 seconds. The interval of sending dummy UDP packet to keep

 

 

 

 

NAT “pin hole” open.

 

 

 

 

 

 

 

 

 

 

 

 

Use NAT IP

 

NAT IP address used in SIP/SDP message. Default is blank.

 

 

 

 

 

 

 

 

 

 

 

 

Firmware Upgrade

 

Default method is HTTP. Firmware upgrade may take up to 10 minutes

 

 

and Provisioning

 

depending on network environment. Do not interrupt the firmware upgrading

 

 

 

 

process.

 

 

 

 

 

 

24

Page 24
Image 24
Grandstream Networks 386 Admin Password, Home NPA, Layer 3 QoS, Layer 2 QoS, No Key Entry, Timeout Stun Server, Use NAT IP