Extreme Series Table SAW | Grizzly G0606X, G0605X instruction

MODEL G0605X/G0606X

EXTREME SERIES

12" TABLE SAW

OWNER'S MANUAL

COPYRIGHT © OCTOBER, 2006 BY GRIZZLY INDUSTRIAL, INC.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL8591 PRINTED IN TAIWAN

Image 1

Grizzly G0606X, G0605X owner manual Extreme Series Table SAW

Contents

Extreme Series Table SAW Page Table of Contents Accessories Maintenance Foreword IntroductionContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW G0606X identification Identification Safety Instructions for Machinery Safety Always Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Protecting Yourself From Kickback Preventing KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Operation Circuit RequirementsAmperage Draw Circuit Requirements Extension Cords Grounding220V Operation 440V Operation Set Up Safety SET UPItems Needed for Set Up Unpacking Fence Inventory Machine InventoryFence Rail Inventory Outfeed Table Inventory Extension Table Inventory Hardware Recognition Chart Placement Location Clean UpSite Considerations Floor Load Extension Table To install the front and rear railsComponents and Hardware Needed Qty Foot installed on support leg Outfeed Table To install the outfeed table Saw Blade To install the blade To install the blade guard To install and adjust the table insertTable Insert Blade Guard Splitter To install the riving knife On/Off SwitchTo install the switch Riving Knife Fence Components To install the miter gaugeMiter Gauge Dust Collection Recommended Recommended adjustment checklistTest Run To connect a dust collection hosePage Operations Operation SafetyBasic Controls Ripping blade features Disabling On/Off SwitchCrosscut blade features Combination blade features Dado Blades Laminate blade features Ripping Non-Through Through CutsNon-Through Cuts Through Cuts Crosscutting To make a crosscut using the miter gauge To perform a miter cut Miter Cuts Dado Cutting To use a standard saw blade to cut dadoes To cut rabbets with the dado blade Rabbet Cutting To cut rabbets with the standard blade Resaw Barrier ResawingComponents Needed for the Resaw Barrier Tools Needed for the Resaw Barrier Resawing Operations Auxiliary FenceComponents Needed for the Auxiliary Fence To build the auxiliary fence To perform resawing operations G7895-Citrus Degreaser AccessoriesH1234-Table Saw Bench Guide H1300 H1298 G7984 H2347 H0736 G2370-SHOP FOX Board Buddies Half-mask respirator and disposable Cartridge filters G3445-Precision Saw Tool G7581-Superbar G7582-Master PlateH3308-SHOP FOX Push Stick H3309-SHOP FOX Featherboard Cleaning MaintenanceSchedule Lubrication Troubleshooting ServiceMotor & Electrical Table Saw Operations Tools Needed Qty Replacing Flat BeltTo remove the flat belt To install the new belt To set the 90 stop bolt Blade Tilt StopsTo set the 45 stop bolt Digital Readout To adjust the tilt indicator arrowTo set the digital readout Miter Slot to Blade Parallelism To adjust the blade parallel to the miter slot Shim procedure diagram a Blade Alignment Adjusting FenceSquare Clamping Pressure If the fence is not parallel to the miter slot Parallelism Date Approximate Hours Of Use Service Performed Service Log G0605X motor junction box G0605X/G0606X Electrical Components G0605X Wiring Diagram G0606X Electrical Components G0606X magnetic switch prewired to Phase G0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Description Cabinet, Motor & Main Table Parts List Description Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page