Guard and ANTI-KICK Back Label | Grizzly G0606X, G0605X instruction

Warning Label Parts List

700

701

709

708

707

706

705

704

702

703 710

REF	PART #	DESCRIPTION

700	P0605X700	GUARD AND ANTI-KICK BACK LABEL
701	P0605X701	DISCONNECT POWER-BLADES LABEL

702	P0605X702	SAFETY GLASSES-HEARING LABEL

703	H7942	EXTREME SERIES PLATE

704	P0605X704	MODEL NUMBER LABEL G0605X

704	P0606X704	MODEL NUMBER LABEL G0606X

705	G8589	GRIZZLY NAMEPLATE-LARGE

REF	PART #	DESCRIPTION

706	P0605X706	MACHINE ID LABEL G0605X
706	P0606X706	MACHINE ID LABEL G0606X

707	PLABEL-12A	READ MANUAL-VERTICAL NS 7/05

708	PLABEL-14	ELECTRICITY LABEL

709	PPAINT-1	GRIZZLY GREEN PAINT

710	PPAINT-11	PUTTY TOUCH-UP PAINT

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

G0605X/G0606X Extreme Series 12" Table Saw

-69-

Image 71

Grizzly G0606X, G0605X owner manual Guard and ANTI-KICK Back Label

Contents

Extreme Series Table SAW Page Table of Contents Accessories Maintenance Contact Info IntroductionForeword Machine Data Sheet Model G0606X 12 Extreme Series Table SAW G0606X identification Identification Safety Instructions for Machinery Safety Always Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Below are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Circuit Requirements Circuit RequirementsOperation Amperage Draw 440V Operation GroundingExtension Cords 220V Operation Unpacking SET UPSet Up Safety Items Needed for Set Up Fence Rail Inventory Machine InventoryFence Inventory Outfeed Table Inventory Extension Table Inventory Hardware Recognition Chart Floor Load Clean UpPlacement Location Site Considerations Components and Hardware Needed Qty To install the front and rear railsExtension Table Foot installed on support leg Outfeed Table To install the outfeed table Saw Blade To install the blade Blade Guard Splitter To install and adjust the table insertTo install the blade guard Table Insert Riving Knife On/Off SwitchTo install the riving knife To install the switch Miter Gauge To install the miter gaugeFence Components To connect a dust collection hose Recommended adjustment checklistDust Collection Recommended Test RunPage Basic Controls Operation SafetyOperations Combination blade features Disabling On/Off SwitchRipping blade features Crosscut blade features Dado Blades Laminate blade features Through Cuts Non-Through Through CutsRipping Non-Through Cuts Crosscutting To make a crosscut using the miter gauge To perform a miter cut Miter Cuts Dado Cutting To use a standard saw blade to cut dadoes To cut rabbets with the dado blade Rabbet Cutting To cut rabbets with the standard blade Tools Needed for the Resaw Barrier ResawingResaw Barrier Components Needed for the Resaw Barrier To build the auxiliary fence Auxiliary FenceResawing Operations Components Needed for the Auxiliary Fence To perform resawing operations H1300 H1298 G7984 H2347 H0736 AccessoriesG7895-Citrus Degreaser H1234-Table Saw Bench Guide G2370-SHOP FOX Board Buddies Half-mask respirator and disposable Cartridge filters H3309-SHOP FOX Featherboard G7581-Superbar G7582-Master PlateG3445-Precision Saw Tool H3308-SHOP FOX Push Stick Lubrication MaintenanceCleaning Schedule Motor & Electrical ServiceTroubleshooting Table Saw Operations To remove the flat belt Replacing Flat BeltTools Needed Qty To install the new belt To set the 45 stop bolt Blade Tilt StopsTo set the 90 stop bolt To set the digital readout To adjust the tilt indicator arrowDigital Readout Miter Slot to Blade Parallelism To adjust the blade parallel to the miter slot Shim procedure diagram a Clamping Pressure Adjusting FenceBlade Alignment Square If the fence is not parallel to the miter slot Parallelism Date Approximate Hours Of Use Service Performed Service Log G0605X motor junction box G0605X/G0606X Electrical Components G0605X Wiring Diagram G0606X Electrical Components G0606X magnetic switch prewired to Phase G0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Description Cabinet, Motor & Main Table Parts List Description Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page