Symptom | Possible Cause | Possible Solution | ||
Machine has vibra- | 1. | Motor or component is loose. | 1. | Inspect/replace stripped or damaged bolts/nuts, and |
tion or noisy opera- |
|
|
| |
tion. | 2. | Flat belt worn or loose. | 2. | Inspect/replace flat belt with new one (refer to Page |
| ||||
|
|
|
| 47). |
| 3. | Motor fan is rubbing on fan cover. | 3. | Replace dented fan cover; replace loose/damaged |
|
|
|
| fan. |
| 4. | Pulley is loose. | 4. | Realign/replace shaft, pulley, set screw, and key as |
|
|
|
| required. |
| 5. | Machine sits unevenly on floor. | 5. | Relocate/shim machine. |
| 6. | Arbor bearings are at fault. | 6. | Replace arbor housing bearings; replace arbor. |
| 7. | Arbor pulley is loose. | 7. | Retighten/replace arbor pulley with shaft and thread |
|
|
|
| locking liquid. |
| 8. | Workpiece is loose. | 8. | Use the correct holding fixture and reclamp |
|
|
|
| workpiece. |
| 9. | Motor bearings are at fault. | 9. | Test by rotating shaft; rotational grinding/loose shaft |
|
|
|
| requires bearing replacement. |
| 10. Blade is at fault. | 10. Replace warped, bent, or twisted blade; resharpen | ||
|
|
|
| dull blade. |
| 11. Loose arbor nut | 11. Tighten the arbor nut. | ||
| 12. Centrifugal switch | 12. Replace centrifugal switch. | ||
|
|
|
| |
Table Saw Operations |
|
| ||
Symptom |
| Possible Cause | Possible Solution | |||
Blade is not aligned | 1. | Blade is warped. | 1. | Replace blade (Page 22). | ||
with miter slot | or | 2. | Table top is not parallel to blade. | 2. | Make table parallel to blade (Page 51). | |
fence. |
|
| 3. | Fence is not parallel to blade. | 3. | Make fence parallel to blade (Page 54). |
|
|
| ||||
|
|
|
|
|
| |
Blade | does not | 1. | 90° stop bolt is out of adjustment. | 1. | Adjust 90° stop bolt (Page 49). | |
reach 90°. |
| 2. | Sawdust loaded up on positive stop. | 2. | Clean sawdust off positive stop. | |
|
|
|
|
|
|
|
Blade | hits insert | at | 1. | 45° stop bolt is out of adjustment. | 1. | Adjust 45° stop bolt (Page 49). |
45°. |
|
| 2. | Hole in insert is inadequate. | 2. | File or mill the hole in the insert. |
|
|
| 3. | Table out of alignment. | 3. | Align blade to the table (Page 51). |
|
|
| 4. | Blade position is incorrect. | 4. | Adjust blade position. |
|
|
|
|
|
|
|
Board | binds | or | 1. | Dull blade. | 1. | Replace blade. |
burns when feeding | 2. | Blade is warped. | 2. | Replace blade (Page 22). | ||
through tablesaw. |
| 3. | Fence is not parallel to blade. | 3. | Make fence parallel to blade (Page 54). | |
|
|
| ||||
|
|
| 4. | Table top is not parallel to blade. | 4. | Make table parallel to blade (Page 51). |
|
|
|
|
|
|
|
G0605X/G0606X Extreme Series 12" Table Saw |
