Manuals / Grizzly / Power Tools / Lathe

Grizzly G0632 owner manual Label Placement

Models: G0632

1 56

Download 56 pages 45.84 Kb

Page 50

Label Placement

118

115

111

114

112

113

116

110

120

119

117

REF	PART #	DESCRIPTION

110	P0632110	MACHINE ID LABEL
111	P0632111	READ MANUAL LABEL VERT
112	P0632112	ENTANGLEMENT LABEL HORZ
113	P0632113	EYE/LUNG LABEL HORZ
114	P0632114	BELT ACCESS LABEL
115	P0632115	CONTROL PANEL LABEL

REF	PART #	DESCRIPTION

116	PPAINT-1	GRIZZLY GREEN TOUCH-UP PAINT
117	PLABEL-14	ELECTRICITY LABEL
118	P0632118	SPINDLE ENTANGLEMENT LABEL
119	P0632119	SMALL INVERTER NOTICE LABEL
120	P0632120	LARGE INVERTER NOTICE LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-48-	G0632 16" x 42" Variable Speed Wood Lathe

Image 50

Grizzly G0632 owner manual Label Placement

Contents

Model G0632 16 X 42 Variable Speed Wood Lathe Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0632 16 x 42 Variable Speed Wood Lathe Identification Page G0632 16 x 42 Variable Speed Wood Lathe G0632 16 x 42 Variable Speed Wood Lathe G0632 16 x 42 Variable Speed Wood Lathe Additional Safety Instructions for Wood Lathes 220V Single-Phase Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingInventory Inventory Figures QtyHardware Recognition Chart Site Considerations Mounting to Shop FloorTo assemble your lathe Clean UpAssembly Tool rest installed on the tool rest Base Test Run To position the headstock along the length of the lathe bed Operation Safety Adjusting HeadstockOperations To position the tailstock along the length of the bed Adjusting TailstockTo swivel the headstock Adjusting Tool Rest To remove the headstock center with the knockout tool Installing/Removing Headstock CenterTo install the headstock center To remove the center from the tailstock quill Installing/Removing Tailstock CenterTo install the center into the tailstock quill Faceplate Turning on To install the headstock faceplateHeadstock Faceplate To change speed ranges Changing Speed RangesDiameter Roughing General Finishing Work Speed range belt positions Indexing Indexing pin and indexing holesSelecting Turning Tools To set up a spindle turning operation Spindle TurningG0632 16 x 42 Variable Speed Wood Lathe Spindle Turning Safety Tips To mount your workpiece to a backing block Faceplate TurningTo mount the workpiece onto the faceplate Outboard Turning Sanding/FinishingH9586-Lathe Fundamentals AccessoriesG1194-3-Jaw Chuck G1082-4-Jaw ChuckModel H6542 Robert Sorby 8-PC Set G9863-8-PC HSS Lathe Chisel SetSchedule MaintenanceCleaning Lathe Bed LubricationService TroubleshootingWood Lathe Operation Service Log Date Approximate Hours Of Use Service PerformedTo align the centers Aligning CentersChanging Belt To change the beltModel G0632 RPM sensor wiring Electrical ComponentsWiring Diagram Overview WiringFrequency Inverter Wiring Diagram Stand & Bed Parts Breakdown Stand & Bed Parts List DescriptionHeadstock Parts Breakdown Headstock Parts List Label Placement Warranty and Returns G0632 16 x 42 Variable Speed Wood Lathe Page Page