Installation procedure | Install wire controller | |
|
|
|
1.Remove the upper cover of wire controller
The PC board is installed on the back cover of wire controller. When remove the upper cover, pay attention not to damage PC board.
Upper cover of wire controller
Back cover of wire controller
Switch |
Screw hole |
2.Install wire controller
Drill 2 wall holes according to the position of the 2 screw holes on the back cover of wire controller, then hit wood in the wall holes. Put the 2 screw h- oles on the back cover of wire controller properly to its corresponding wood, then use wood screws to fix the back cover on the wall.
Note:
Install the back cover of wire controller on the even wall as possible as can. When tightening the wood screw, do not use to tight force, otherwise the wire controller may be damaged.
Switch
Mark | ON | OFF | |
1 | 3 grades fan speed | 2 grades fan speed | |
2 | Have rise and drop | No rise and drop | |
3 | Swing | Not Swing | |
4 | The collection temperature | The collection temperature | |
of main panel | of panel | ||
|
Under this series, the switch is set as:1.ON 2. OFF 3. OFF 4.OFF
3.Indoor unit wire connection
Connect the terminals (A, B, C, D,) on the wire controller to the terminals on the indoor PC panel (A, B, C, D,) respectively.
Arrange wire
AB CD from this part
Back cover wire controller
Note:When connecting wire, please keep a certain distance between signal wire and electric wire. (over 10mm)
|
|
|
|
|
|
|
|
| Dimension of signal wire: | ||||||||||||
|
|
|
|
|
|
|
|
|
| Type of wire Shield wire (4 cords) |
| ||||||||||
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
| Dimension |
| 0.33mm2 |
| ||||||||
|
|
|
|
|
|
|
| Upper cover of | *The connection between indoor unit | ||||||||||||
|
|
|
|
|
|
|
|
| and wire controller and indoor unit | ||||||||||||
|
|
|
|
|
|
|
| wire controller |
| ||||||||||||
|
|
|
|
|
|
|
|
|
| and outdoor unit should use shield | |||||||||||
Note: |
| wire. And the two ends of the shield | |||||||||||||||||||
| wire should be grounded, otherwise, | ||||||||||||||||||||
Confirm the connection part of terminals |
| ||||||||||||||||||||
| the disturbance will cause unit abn- | ||||||||||||||||||||
is firm and will not touch shield wire. |
| ||||||||||||||||||||
| ormal operation. |
|
|
|
|
|
| ||||||||||||||
4. Cover the wire controller upper cover |
|
|
|
|
|
|
| ||||||||||||||
Pay attention not to press the connection wire. |
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Shield wire |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| Note: (1) The power switch and the signal |
| Grounded |
| Grounded | ||||||||||||||||
|
|
|
| wire are |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
26 |
|
| (2) Do not touch PC board by hand. |
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|