Note

The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.

Operation
Controller Operation

To control a device using the Controller

1. Program the Controller to work with your device.
2. Changing device mode by pressing the SELECT key. Default device is TV. When press SELECT
key, current device led will be on. Keep pressing SELECT key to choose a device, the loop is:
TV DVD VCR STB Cable Audio - TV. When device is set, related device LED will be on for 5
seconds and then be off.
3. Aim the remote at the device.
4. Press the POWER button to turn the device on.
5. Use the other Controller buttons to operate the device. Device LED will blink if user presses any
key (if the key has data in current mode.). If the key has no data, then LED will not blink.
6. Default init status: TV/Haier 001 code.
7. Bulb key to control the flash light.
Programming the Controller
The Controller is factory-programmed to support up to 600 code sets.
There are two ways to program the Controller:
Selecting a brand code for the device you wish to operate, and then entering that code manually
into the Controller.
Using the Power Scan feature to find device codes automatically.
The two programming methods are described in the following sections.
Manually Programming the Controller
1. Using SELECT key to choose the device you want to program.
2. While Press and holding OK key, press SELECT key, and device LED will be ON. Keep the status
for about 5 seconds, release both keys and then LED will blink twice per second, indicating that
the Controller is ready for programming.
3. Led will blink once when you enter a digit key, indicating the digit key is programmed. If 3 digits
are programmed successfully, device LED will be ON for about 3 seconds and then blink twice
per second. Then User now can:
a) Try to operate the device by using POWER or PLAY keys. If operation can be done, press OK
to save current 3-digits code and exiting manually programming mode.
b) Return to beginning of step 3. Reprogram the controller.
5. If user's input is incorrect, LED will blink 12 times in 3 seconds. And then keep twice per second
blink, user now can return to step 3 and re-program the device.
6. Within 10 seconds, user should enter the 3-digit brand code corresponding to your device. If time
out or any key other than POWER PLAY and digits is pressed, LED will be off and manually
programming process is exit.
7. Fast Programming Haier default TV code set. Press and holding the EXIT key and then press
SELECT key for 5 seconds, default Haier code set (001) will be programmed to the controller.
Manually scan mode
With manually scan programming, the Controller tests all the codes available in the code set data
base and assign the correct one for the selected device.
To manually-scan program the Controller:
1. Manually turn OFF the device for manually scan mode. (TV, VCR, DVD, STB, cable box or audio
equipment).
2. Press SELECT key to choose the device you wish to program.
While Press and holding OK key, press the SELECT key and device LED will be ON. Keep the
status for about 5 seconds, release both keys and then LED will blink twice per second,
indicating that the Controller is ready for programming.
3. Press and release the CH+/CH- key. The LED blinks 10 times per seconds, indicating that the
Remote is in manually scan mode.
4. Press CH+/CH- key repeatedly until the device switches ON (CH+ key conducts a upward
search while the CH- key conducts a downward search in the code set database).
5. When the device turns ON, press and release the OK key to program the Controller with the
new code, saving the code and exit. To exit without programming, press any key other except
CH+/CH- and OK. LED will be off after manually scan mode is exit.
6. If the device responds, no further programming is required. If the device does not respond,
repeat step 1 through 5.And searching will start from current code set. If no key was pressed
in 30 seconds, manually scan mode will be automatically exit.
7. After searching the entire data base, this mode will be automatically exited and led will blink for
3 times.
Setting Up Your Remote Control

After it has been set up properly, your remote control can operate in six different modes:

TV, VCR, CABLE, DVD, SETBOX or AUDIO Pressing the corresponding button on the remote control

allows you to switch between these modes, and control whichever piece of equipment you choose.

.

Owner s Manual 31