INSTALLATION

(825mm), a maximum depth of 36" (914mm), and minimum height of 24" (610mm) from top of unit to ceiling.

6)We recommend that you plan your instal- lation on paper using exact measurements for clearances and fl oor protection before actually installing this appliance. Have a qualifiedbuildinginspectorreviewyourplans before installation.

GENERAL SAFETY

INFORMATION

1)The appliance installation must conform with local Canadian Electrical Code.

2)The appliance when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code, ANSI/NFPA 70 or CSA C22.1 Canadian Electrical Code.

3)The appliance should be inspected for ship- ping damage before use and serviced an- nually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, and circulating air passage- ways of the appliance be kept clean and free from excessive lint from carpeting.

4)See general construction and assembly instructions. The appliance and vent should be enclosed when installed in or passing through a living area, where children may come in contact with it.

5)This appliance must be connected to the specifi ed vent and termination cap to the

outside of the building envelope. Never

vent to another room or inside a building. Make sure that the vent is fi tted as per the instructions starting in the "Exterior Vent Terminal Locations" section.

6)Inspect the venting system annually for blockage and any signs of deterioration.

7)Venting terminals shall not be recessed into a wall or siding.

8)Any safety glass removed for servicing must be replaced prior to operating the appli- ance.

9)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fi replace.

Emissions from burning wood or gas could contain chemicals known to the State of Cali- fornia to cause cancer, birth defects or other reproductive harm.

INSTALLATION

CHECKLIST

1)Locate your gas appliance. Refer to the following sections:

a.Locating Your Gas Stove

b.Clearances to Combustibles

c."Venting Introduction" to "Exterior Vent Terminal Locations" sections.

2)Install Optional Fan. Refer to the "Optional Fan Installation" section.

3)Set vent restrictor. Refer to the "Vent Restric- tor Position" section.

4)Install venting: Check all venting require- ments. See "Venting Introduction" to "Dura- Vent Vertical Termination" sections.

5)Make gas connections. Refer to the "Gas Connection" section.

Test the pilot. Must be as per diagram in the "Pilot Adjustment" section.

If converting to Propane, make changes prior as instructed in the "Conversion from Natural Gas to Propane" section.

6)Test Gas Pressure. Refer to the "Gas Pipe Pressure Testing" section.

7)Install standard and optional features. Refer to the following sections where applicable:

a.Log Set Installation

b.Wall Thermostat

c.Remote Control

8)Final check. Refer to the "Final Check" sec- tion.

Before leaving this unit with the customer, the installer must ensure that the appliance is fi r- ing correctly and operation fully explained to customer.

This includes:

1)Clocking the appliance to ensure the correct fi ring rate (rate noted on label) after burning appliance for 15 minutes.

2)Ifrequired,adjustingtheprimaryairtoensure that the fl ame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

CLEARANCES TO

COMBUSTIBLES

The clearances listed are MINIMUM distances. Measure the clearance to both the appliance and the chimney connector. The farthest distance is correct if the two clearances do not coincide.

For example, if the appliance is set as indicated in one of the fi gures but the connector is too close, move the stove until the correct clearance to the connector is obtained.

This appliance may be installed only with the clearances as shown in the situations pictured.

Do not combine clearances from one type of installation with another in order to achieve closer clearances.

This unit can be installed on a solid combustible surface like a wood fl oor. This unit can also be installed directly on carpeting or vinyl.

Use the minimum clearances shown in the diagrams below:

H15-NG1 & H15-LP1 Clearances

A Left Side Wall to Unit*

6"

/ 150 mm

*BBack Wall to Unit

0"

/ 0 mm

C Vertical Vent Pipe to Back Wall

 

 

2" / 50 mm

E Unit Corner to Wall

2"

/50 mm

Unit Top to Alcove Ceiling

24"

/ 610 mm

Minimum ceiling height is 24" /610 mm from

top of unit.

*IMPORTANT

It is recommended that unit is moved away from

the wall, if installing the blower option, so the fan

can be easily installed and/or serviced.

Hampton® H15-1 Direct Vent Freestanding Gas Stove

7

Page 6 Page 8
Page 7
Image 7
Hampton Direct H15-LP1 General Safety Information, Installation Checklist, Clearances to Combustibles, This includes
Page 6 Page 8

H15-LP1, H15-NG1 specifications

Hampton Direct has established a reputation for producing innovative and high-quality products, and their H15-NG1 and H15-LP1 appliances are no exceptions. These two models have been thoughtfully designed to cater to different needs while sharing several essential features that promise reliability and performance.

The H15-NG1 is designed as a natural gas appliance, ideal for users who prefer the efficiency and cost-effectiveness of natural gas heating. Its advanced technology ensures that it operates smoothly and efficiently, providing consistent heating without compromising safety. Users can appreciate the integrated safety features, including automated shut-off mechanisms and flame detection systems. The H15-NG1 also has adjustable heat settings, giving users the flexibility to control the temperature according to their requirements.

On the other hand, the H15-LP1 is specifically designed for propane users. This model is perfect for those who utilize propane as a primary energy source in their households. Similar to its counterpart, the H15-LP1 boasts a powerful heating system that can quickly warm up large spaces, making it an excellent choice for both indoor and outdoor applications. It also includes safety features such as a pressure regulator, ensuring a stable flow of propane that enhances both efficiency and safety.

Both the H15-NG1 and H15-LP1 are constructed with durable materials, ensuring longevity and resilience in various conditions. They are easy to install and user-friendly, making them suitable for users of all experience levels.

Another significant feature of both models is their energy efficiency, which not only provides savings on utility bills but also contributes to an eco-friendly lifestyle. They are equipped with innovative heating technology that maximizes heat output while minimizing energy consumption. This focus on sustainability aligns with contemporary standards for energy-efficient home appliances.

In summary, the Hampton Direct H15-NG1 and H15-LP1 offer impressive features and technologies designed to meet diverse heating needs. With a commitment to safety, efficiency, and user convenience, these models stand out as reliable choices for homeowners looking for effective heating solutions. Whether you prefer natural gas or propane, both units promise a blend of performance, durability, and ease of use.
Top Page Image Contents