Hampton Direct H15-LP1, H15-NG1 IMPORTANT MESSAGE SAVE THESE , SPECIFICATIONS, MOBILE / MANUFACTURED HOMES AFTER FIRST SALE, BEFORE YOU START

6Hampton® H15-1 Direct Vent Freestanding Gas Stove

IMPORTANT MESSAGE SAVE THESE

INSTRUCTIONS

The Direct Vent Freestanding Gas Stove must

be installed in accordance with these instruc-

tions. Carefully read all the instructions in this

manual ﬁ rst. Consult the building authority

having jurisdiction to determine the need for a

permit prior to starting the installation.

Note: Failure to follow the instructions

could cause a malfunction of the

heater which could result in death,

serious bodily injury, and/or prop-

erty damage. Failure to follow these

instructions may also void your ﬁ re

insurance and/or warranty.

Note: These instructions take precedence

over Simpson Dura-Vent instruc-

tions.

SPECIFICATIONS

Fuels: H15-NG1 is approved for use with

natural gas.

H15-LP1 is approved for use with liq-

ueﬁ ed petroleum gases (propane).

Electrical: 120V A.C. system.

Optional Circulation Fan:

Variable speed, 125/75.

Log Sets: Ceramic ﬁ bre, 4 per set.

Vent System: Coaxial (6-5/8" outer / 4" inner

liner) rigid ﬂ ue and termination cap.

MOBILE / MANUFACTURED HOMES AFTER FIRST SALE

This Hampton® product has been tested and

listed by ITS Testing Services as a Direct Vent

Room Heater to the following standards:

CGA-2.17-M91, and ANSI Z21.88B-2003/CSA

2.33B-2003.

This Direct Vent System Appliance must be

installed in accordance with the manufacturer's

installation instructions and the Manufactured

Home Construction and Safety Standard, Title

24 CFR, Part 3280, or the current Standard of

Fire Safety Criteria for Manufactured Home In-

stallations, Sites, and Communities ANSI/NFPA

501A, and with CAN/CSA Z240-MH Mobile

Home Standard in Canada.

INSTALLATION

This appliance installation must comply with the

manufacturer's installation instructions and local

codes, if any. In the absence of local codes fol-

low the current National Fuel Gas Code, ANSI

Z223.1 and the current National Electrical Code

ANSI/NFPA 70 in the U.S.A., and the current

CAN/CGA B149 Gas Installation Code and the

current Canadian Electrical Code CSA C22.1

in Canada.

This Hampton® Mobile/Manufactured Home

Listed appliance comes factory equipped

with a means to secure the unit.

This Hampton® Mobile/Manufactured

Home listed appliance comes equipped

with a dedicated #8 ground lug to which

an 18 gauge copper wire from the steel

chassis ground must be attached.

This appliance may only be installed in

an aftermarket permanently located,

manufactured (USA only) or mobile

home, where not prohibited by local

codes.

This appliance is only for use with

the type of gas indicated on the rating

plate. This appliance is not convert-

ible for use with other gases, unless

a certiﬁ ed kit is used.

INSTALLATION AND REPAIRS

SHOULD BE DONE BY A QUALI-

FIED SERVICE PERSON. THIS AP-

PLIANCE SHOULD BE INSTALLED,

REPAIRED, INSPECTED BEFORE

USE AND AT LEAST ANNUALLY

BY A QUALIFIED SERVICE PER-

SON. MORE FREQUENT CLEAN-

ING MAY BE REQUIRED DUE TO

EXCESSIVE LINT FROM CARPET-

ING, ETC. IT IS IMPERATIVE THAT

THE CONTROL COMPARTMENT,

BURNERS AND CIRCULATING

AIR PASSAGEWAYS OF THE AP-

PLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES,

THE APPLIANCE SHOULD BE

LOCATED OUT OF TRAFFIC AND

AWAY FROM FURNITURE AND

DRAPERIES.

BEFORE YOU START

Safe installation and operation of this appli-

ance requires common sense, however, we

are required by the Canadian Safety Standards

and ANSI Standards to make you aware of the

following:

1) Provide adequate clearances for servicing,

proper operation and around the air openings

into the combustion chamber.

2) The appliance must be installed on a ﬂ at,

solid, continuous surface (e.g. wood, metal,

concrete). This may be the ﬂ oor, or it can be

raised up on a platform to enhance its visual

impact. The appliance may be installed on

carpeting, tile, wood ﬂ ooring or other com-

bustible material, because the appliance's

base extends the full width and depth of the

appliance. The Direct Vent Freestanding

Gas Stove can be installed in a wide variety

of ways and will ﬁ t nearly any room layout.

It may be installed in a recessed position,

framed out into the room, or across a cor-

ner.

3) The Direct Vent Freestanding Gas Stove is

approved for alcove installations, which meet

the clearances listed in the "Clearance to

Combustibles" section. This unit is approved

for manufactured home installations, see

the "Manufactured Mobile Home Additional

Requirements" and "Rigid Pipe Venting

Systems" sections for the required vent ar-

rangements. If installed into a manufactured

home the unit must be bolted down to the

ﬂ oor.

4) This appliance is Listed for bedroom instal-

lations when used with a Listed Millivolt

Thermostat. Some areas may have further

requirements, check local codes before

installation.

5) This appliance is Listed for Alcove installa-

tions, maintain minimum Alcove clearances

as follows, minimum width of 32-1/2"

WARNING: FAILURE TO INSTALL

THIS APPLIANCE CORRECTLY

WILL VOID YOUR WARRANTY

AND MAY CAUSE A SERIOUS

HOUSE FIRE.

CHILDREN AND ADULTS SHOULD

BE ALERTED TO THE HAZARDS

OF HIGH SURFACE TEMPERA-

TURES, ESPECIALLY THE FIRE-

PLACE GLASS, AND SHOULD

STAY AWAY TO AVOID BURNS

OR CLOTHING IGNITION.

YOUNG CHILDREN SHOULD

BE CAREFULLY SUPERVISED

WHEN THEY ARE IN THE SAME

ROOM AS THE APPLIANCE.

CLOTHING OR OTHER FLAM-

MABLE MATERIAL SHOULD NOT

BE PLACED ON OR NEAR THE

APPLIANCE.