Manuals / HandHeld Entertainment / Computer Equipment / Scanner

HandHeld Entertainment manual Enabling QCID for Bluetooth, Quick Check 890 User’s Guide

Models: Quick Check 890

1 40

Page 14

You will be asked if you need a passkey to add your device. The default passkey for all Hand Held Products QC890 verifiers is “1234.”

The Wizard loads the QC890 Verifier information into your device. You may click a checkbox to indicate the QC890 Verifier is the default device to which Quick Check ImageData connects.

Once you select Finish, your device is ready to communicate with the QC890 Verifier via the assigned ports. Make a note of the assigned port number. You will need to know this port number in the following installation steps.

Enabling QCID for Bluetooth

1.Once you open the QCID application, click on File -> Preferences.

2.Choose the assigned incoming port number reported in the Add Bluetooth Device wizard and click OK.

3.Your QC890 Verifier connects to the QCID application.

2 - 6

Quick Check® 890 User’s Guide

Page 14

Image 14

HandHeld Entertainment manual Enabling QCID for Bluetooth, Quick Check 890 User’s Guide

Contents

Barcode Verifier Quick Check Quick Check ImageDataUser’s Guide Disclaimer Chapter 2 - Quick Check ImageData Table of ContentsChapter 1 - Getting Started Appendix B - Menu Setting Barcodes Chapter 3 - Using the Quick Check 890 Verifier SystemChapter 4 - Maintenance Appendix C - Symbology Defaults - OperationIntroduction QC890 Verifier FeaturesGetting Started Unpacking the QC890 VerifierScan Button LEDs Using the QC890 VerifierScan Button Quick Check 890 User’s GuideUser LED Indications Special FeaturesPhysical Connections Audio SoundCharging the Battery SpecificationsInternal Battery Powering On the QC890 VerifierQuick Check ImageData Installation of Quick Check ImageDataQuick Check ImageData System RequirementsNote No additional configuration e.g., baud rate is necessary USB Communication InterfaceUSB COM Port Emulation Quick Check 890 User’s GuideRS-232 Selections BluetoothRS-232 Serial Communication Interface Quick Check 890 User’s GuideUsing the QC890 Verifier with Bluetooth Devices Quick Check 890 User’s GuideEnabling Your Device for Bluetooth Quick Check 890 User’s GuideEnabling QCID for Bluetooth Quick Check 890 User’s GuidePC Main Screen Using Quick Check ImageDataQuick Check 890 User’s Guide PDA Main Screen Help SystemQuick Check 890 User’s Guide Scanning a Barcode Symbol Using Quick Check ImageData Using the Quick Check 890 Verifier SystemScanning a Barcode Symbol Using the QC890 Verifier Quick Check 890 User’s GuideCalibrating the QC890 Verifier Quick Check 890 User’s GuideScanning Properly Using a Pen/Mouse Wand Quick Check 890 User’s GuideCalibrating an External Pen/Mouse Wand Quick Check 890 User’s GuideNote The QC3800VE reading width includes quiet zones is 6 inches Scanning Properly Using the QC3800VE Linear ImagerQuick Check 890 User’s Guide Quick Check 890 User’s Guide Calibration LogReflectometer Mode Quick Check 890 User’s Guide 1. To activate the Reflectometer, click on the Reflectometer iconQuick Check 890 User’s Guide QC890 Verifier MaintenanceCleaning the External Devices RecertificationQuick Check 890 User’s Guide Quick Check 890 User’s Guide Customer SupportTechnical Assistance North America/CanadaFor Further Information Product Service and RepairOnline Technical Assistance E-mail naservice@handheld.comE-mail apservice@handheld.com Limited WarrantyOnline Product Service and Repair Assistance Quick Check 890 User’s GuideQuick Check 890 User’s Guide 2 yearsX Dimension AperturesPen/Mouse Wand Aperture Selection X DimensionQuick Check 890 User’s Guide Illumination Timer Menu Setting BarcodesResetting the Standard Product Defaults Standard Product Default Settings barcode belowQuick Check 890 User’s Guide Power Down TimerNote This option applies to battery operation only Symbology Defaults - Operation Quick Check 890 User’s GuideQuick Check 890 User’s Guide Page Page Page QC890-UG Rev C 1/08 Hand Held Products, Inc700 Visions Drive P.O. Box Skaneateles Falls, NY