Harman-Kardon AVR 354 Connecting Source Devices to the AVR, Types of Connections, Subwoofer

CONNECTIONS

There are different types of audio and video connections used to connect the receiver to the speakers and video display, and to connect the source devices to the receiver. To make it easier to keep them all straight, the Consumer Electronics Association has established the CEA® color-coding standard. See Table 1.

Table 1 – Connection Color Guide

Audio Connections

LeftRight

Front (FL/FR)

Center (C)

Surround (SL/SR)

Surround Back (SBL/SBR)

Subwoofer (SUB)

Digital Audio Connections

Coaxial

OpticalInput

Video Connections

Component	Y	Pb	Pr
Composite
S-Video

HDMI™ Connections (digital audio/video)

HDMI

Types of Connections

This section will briefly review different types of cables and connections.

Speaker Connections

Speaker cables carry an amplified signal from the receiver’s speaker terminals to each loudspeaker. Speaker cables contain two wire conduc- tors, or leads, inside plastic insulation. The two conductors are usually differentiated in some way, by using different colors, or stripes, or by adding a ridge to the insulation. Sometimes the wires are different, colors e.g. copper-colored and silver.

The differentiation is important because each speaker must be connected to the receiver’s speaker-output terminals using two wires, one positive

(+)and one negative (–), referred to as speaker polarity. It’s important to maintain the proper polarity for all speakers in the system, or perform- ance can suffer, especially for the low frequencies.

Always connect the positive terminal on the loudspeaker, which is usually colored red, to the positive terminal on the receiver, which is colored as shown in the Connection Color Guide (Table 1). Similarly, always connect the black negative terminal on the speaker to the black negative terminal on the receiver.

	The AVR 354 uses binding-post speaker
	terminals that can accept banana plugs
+	or bare-wire cables. Banana plugs are
	simply plugged into the hole in the middle
	of the terminal cap. See Figure 1.

Figure 1 – Binding-Post Speaker Terminals With Banana Plugs

Bare wire cables are installed as follows (see Figure 2):

1.Unscrew the terminal cap until the pass-through hole in the collar is revealed.

2.Insert the bare end of the wire into the hole.

3.Hand-tighten the cap until the wire is held snugly.

1 2 3

Figure 2 – Binding-Post Speaker Terminals With Bare Wires

Subwoofer

The subwoofer is a specialized type of loudspeaker used to play only the low frequencies (bass), which require much more power than the other speaker channels. In order to obtain the best results, most speaker manufacturers offer powered subwoofers, in which the speaker contains its own amplifier on board. Usually, a line-level (nonamplified) connection is made from the receiver’s Subwoofer Output to a corresponding jack on the subwoofer, as shown in Figure 3, but sometimes the subwoofer is connected to the receiver using the front left and right speaker outputs, as with passive in-wall subwoofers, and then the front left and right speakers are connected to terminals on the subwoofer.

Although the subwoofer output looks similar to the analog audio jacks used for the various components, it is filtered and only allows the low frequencies to pass. Don’t connect this output to any other devices.

Although doing so won’t cause any harm, performance will suffer.

Preout Subwoofer

Figure 3 – Subwoofer

Connecting Source Devices to the AVR

The AVR 354 is designed to process audio and video input signals, playing back the audio and displaying the video on a television or monitor connected to the AVR. These signals originate in what are known as “source devices,” including your DVD player, CD player, DVR (digital video recorder) or other recorder, tape deck, game console, cable or satellite television box or MP3 player. Although the tuner is built into the AVR, it also counts as a source, even though no external connections are needed, other than the FM and AM antennas and the XM antenna module.

Separate connections are required for the audio and video portions of the signal, except for digital HDMI connections. The types of connections used depend upon what’s available on the source device, and for video signals, the capabilities of your video display.

19