MAIN REMOTE CONTROL FUNCTIONS
MTuning Up/Down: When the tuner is in use, this button will tune up or down through the selected fre- quency band. If the Tuning Mode Button B6 has been pressed so that AUTO appears in the Lower Display Line B, pressing either button will cause the tuner to seek the next station with acceptable signal strength for quality reception. When MANUAL appears in the Lower Display Line B, pressing this button will tune stations in
NDisc Skip Button: This button has no direct function for the DPR 1001 but may be used to change the disc in a CD or DVD changer when the remote is programmed for that type of device. (See page 35 for more information.)
OProgram Button: This button is used to begin the process of programming the remote. Press and hold this button for three seconds to place the remote in the programming mode. Once the red LED under the Set Button F lights, release the button. You may then select from the desired option. (See pages
PLight Button: Press this button to activate the remote’s backlight for ease of use in darkened rooms.
QMultiroom: Press this button to activate the multi- room system or to begin the process of changing the input or volume level for the second zone. (See page 31 for more information on the multiroom system.)
Macro Buttons: Press these buttons to store or recall a “Macro”, which is a preprogrammed sequence of commands stored in the remote. (See page 35 for more information on macros.)
Sleep Button: Press this button to place the unit in the Sleep mode. After the time shown in the display, the DPR 1001 will automatically go into the Standby mode. Each press of the button changes the time until
|
| 90 |
| 80 |
|
| 70 |
|
| 60 |
|
| 50 |
| |
|
| min |
| min |
| min |
| min |
|
|
| min |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 40 |
| 30 |
|
| 20 |
|
| 10 |
|
|
| OFF | ||
|
|
|
|
|
|
|
|
| |||||||
|
| min |
| min |
| min |
| min |
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||||||
Night Mode: Press this button to activate the Night mode. This mode is available in specially encoded Dolby Digital sources, and it preserves dialogue (center channel) intelligibility at low volume levels.
OSD Button: Press this button to activate the
Tone Control Button: This button controls whether or not the Bass and Treble controls are active, and, if so, the degree to which they are used. The first press of this button tells the current status of the tone controls: If TONE OUT is displayed in the Lower
Display Line B, the tone controls are not in the signal path, and the DPR’s output is “flat.” If TONE IN is displayed, the controls are active. To switch the tone controls in or out, press the ⁄/¤ Navigation Button
nso that the desired setting appears. To change the actual bass or treble settings, first make certain that TONE IN has been activated, and then press the button again so that either BASS MODE or TREBLE MODE appears. Within five seconds, press the ⁄/¤ Navigation Button n to enter the desired setting.
Mute: Press this button to momentarily silence the DPR 1001 or TV set being controlled, depending on which device has been selected.
AM/FM Tuner Select: Press this button to select the DPR 1001’s tuner as the listening choice. Pressing this button when the tuner is already in use will select between the AM and FM bands.
Channel Up/Down Selector: These buttons have no function when the DPR is being controlled, but when programmed for use with a VCR, TV, cable box, satellite receiver or other similar product they will change the channel up or down. See pages
Delay/Select: Press this button to begin the process for setting the delay times used by the DPR 1001 when processing surround sound. After pressing this button, the delay times are entered by pressing the Set Button F and then the ⁄/¤ Navigation Button n to change the setting. Press the Set Button F again to complete the process. (See page 21 for more information on setting delay times.)
Speaker Select: Press this button to begin the process of configuring the DPR 1001’s bass management system. Then press the ⁄/¤ Navigation Button n to select the channel you wish to set up. Press the Set Button F and then select the speaker type. When all adjustments have been completed, press the Set Button F twice to exit the settings and return to normal operation. (See page 19 for more information on speaker setup.)
Memory Button: Press this button to enter a radio station into the DPR 1001’s preset memory. Once PRESET MEMORY flashes in the Lower Display Line B, you have five seconds to enter a preset memory location using the Numeric Keys A. (See page 28 for more information.)
Stereo Mode Selector: Press this button to select a stereo listening mode. The first press of the button places the DPR 1001 in a true,
DTS Neo:6 Mode Selector: Press this button to select a DTS Neo:6 mode. (See page 26 for the available DTS Neo: 6 options.)
DTS Digital Mode Selector: When a DTS- encoded digital source is playing, each press of this button will scroll through the available DTS modes. The specific choice of modes will vary according to the type of encoding on the disc and your system’s speaker configuration. When a DTS source is not in use, this button has no function. (See page 26 for the available DTS digital options.)
Dolby Surround Mode Selector: This button is used to select from the available Dolby Surround modes. Each press of this button will select one of the Dolby Pro Logic II modes or Dolby 3 Stereo. When a Dolby
34. (See page 29 for more information.)
SPL Select: This button activates the DPR 1001’s EzSet function to quickly and accurately calibrate the DPR 1001’s output levels. When the button is pressed you will then need to select between automatic EzSet operation or using the remote as a manual SPL meter by pressing the ⁄/¤ Navigation Button n until your choice appears in the remote’s LCD display. Press the Set Button F to enter the setting, and then follow the instructions as displayed in the LCD display. For complete information, see page 22.
EzSet Microphone Sensor: The microphone sensor that is used by the EzSet system is behind the three slots at the top of the remote control. When using EzSet to calibrate the DPR 1001 be certain that the slots are not covered. (See page 22 for more information on using EzSet.)
Lens: The infrared emitters behind the plastic lens at the top of the remote communicate the remote codes to the DPR 1001. Be certain that the lens is not covered when using the remote, and point the lens toward the DPR for best results. In learning mode, the remote receives IR codes to be learned through a sensor behind the lens.
NOTE: DO NOT remove the rubber plug that is supplied to cover the jack on the upper right side of the remote. The jack is not active and is reserved for future use.
