SYSTEM CONFIGURATION
option of SIZE, and then proceed as outlined below. Once the speaker choices have been set you may wish to return to this line to change the option so that the crossover settings may be adjusted.
Begin the speaker setup process by making certain that the LEFT/RIGHT line is highlighted in reverse video, which sets the configuration for the front left and right speakers. If you wish to make a change
to the front speakers’ configuration, press the ‹/› Navigation Buttons n so that either LARGE or SMALL appears, matching the appropriate description from the definitions on page 19.
When SMALL is selected,
When LARGE is selected, a
NOTE: When the front speakers are set to the LARGE option and the surround mode is set to "Surround Off," or pure
choose the INDEPENDENT setting on the BASS MGR line at the bottom of this menu so
that only those inputs where the analog bypass is desired will be routed in this fashion, while other analog inputs such as a VCR or cable box will be digitized for surround processing.
When you have completed your selection for the front channel, press the ¤ Navigation Button n to move the highlighted video to CENTER.
Press the ‹/› Navigation Buttons n to select the option that best describes your system, based on the definitions shown on page 19.
When SMALL is selected,
When LARGE is selected, a
NOTE: If you choose Logic 7 as the surround mode for
the particular input source for which you are configuring your speakers, the DPR 1001 will not make the LARGE option available for the center speaker. This is due to the requirements of Logic 7 processing, and does not indi- cate a problem with your receiver.
When NONE is selected, no signals will be sent to the center channel output. The receiver will operate in a “phantom” center channel mode and center channel information will be sent to the left and right front channel outputs. When only front left and right speakers are used, with no center or surround speakers, VMAx is a good alternative mode.
When you have completed your selection for the center channel, press the ¤ Navigation Button n to move the highlighted video to SURROUND.
Press the ‹/› Navigation Buttons n to select the option that best describes the surround speakers in your system based on the definitions shown on page 19.
When SMALL is selected,
When LARGE is selected, a
When NONE is selected, surround sound information will be split between the front left and front right outputs.
When you have completed your selections for the main surround channels, press the ¤ Navigation Button
nto move the highlighted video to SURR
BACK. This line enters the setting for the surround back channels when they are present, and it also tells the DPR 1001’s processing system to configure the unit for either 5.1 or 6.1/7.1 operation.
Press the ‹/› Navigation Buttons n to select the option that best describes the speakers in use at the left and right back surround positions based on the defini- tions on page 19.
When NONE is selected, the system will adjust so that only
When SMALL is selected the system will adjust so that the full complement of 6.1/7.1 surround modes is available, and
If you choose this option with no subwoofer connected,
you will not hear
When LARGE is selected the system will adjust so that the full complement of 6.1/7.1 surround modes is available, and a
When you have completed your selection for the back surround channels, press the ¤ Navigation Button n on the remote to move the highlighted video to SUBWOOFER.
Press the ‹/› Navigation Buttons n to select the option that best describes your system.
The choices available for the subwoofer position will depend on the settings for the other speakers, particular- ly the front left/right positions.
If the front left/right speakers are set to SMALL, the subwoofer will automatically be set to SUB.
If the front left/right speakers are set to LARGE, three options are available:
•If no subwoofer is connected, press the ‹/› Navigation Buttons n so that SUB NONE appears in the
•If a subwoofer is connected, you have the option to have the front left/right “main” speakers reproduce bass frequencies at all times, and have the sub- woofer operate only when a digital source with a dedicated
•To use a subwoofer for bass reproduction in con- junction with the main front left/right speakers, regardless of the type of program source or Surround mode you are listening to, press
the ‹/› Navigation Buttons n so that L/R+LFE appears. When this option is selected, a
When all initial speaker “size” settings have been made, you may then take advantage of the DPR 1001’s Triple Crossover system, which allows individual crossover settings to be made for each speaker grouping. The low- frequency crossover point is set by the design of your speakers. Depending on the design and driver comple- ment of your speakers, it is defined as the frequency which is either the lowest possible frequency the speaker