3. (Note: The parts shown in this step may be preassembled.) | 3 |
|
|
|
| |
| With the help of a second person, raise the Frame (55) and |
|
|
|
| |
|
|
|
|
|
| |
| hold it. Insert the Left Frame Guide (68) into the left side of |
|
|
|
|
|
| the Frame. Remove the Lock Knob (67) from the Lock Pin |
| Hole |
|
|
|
| (72). Make sure that the Lock Pin Collar (70) and the Spring |
| 55 | 129 |
| |
| (69) are on the Lock Pin. Insert the Lock Pin into the Frame |
|
| 5 |
| |
|
|
| 70 |
| ||
| and the Left Frame Guide. Press the Latch Insert (5) onto |
|
|
|
| |
|
|
| 72 |
|
| |
| the Frame, with the Lock Pin in the center hole. Tighten the |
|
|
|
| |
|
|
|
|
|
| |
| Lock Knob onto the Lock Pin. |
|
|
| 69 | 67 |
|
| 68 |
|
| ||
|
| 62 |
|
| ||
| Align the Lock Pin (72) with the hole in the Left Foam Grip |
|
|
| ||
|
|
|
|
|
| |
| (62) by sliding the Left Frame Guide (68) up or down. |
|
|
|
|
|
| Make sure that the Lock Pin can be inserted fully into the |
|
|
|
|
|
| hole. Hold the Left Frame Guide in place as you tighten |
|
|
|
|
|
| two 1/2” Screws (129) into the Latch Insert and the Left |
|
|
|
|
|
| Frame Guide. Note: It may be necessary to pull the Lock |
|
|
|
|
|
| Knob (67) to access and tighten the Screws. |
|
|
|
|
|
4. | Put the treadmill in the storage position (see HOW TO | 4 |
|
|
|
|
| FOLD THE TREADMILL FOR STORAGE on page 21). | 26 |
| 51 |
|
|
|
|
|
|
| ||
| Have a second person hold the treadmill in the upright posi- | 130 |
|
|
|
|
|
|
|
|
|
| |
| tion. Place the |
|
|
|
|
|
| (65) as shown. Make sure that the |
|
|
|
|
|
| the Bumpers (98) are on the bottom. Finger tighten two |
|
|
|
|
|
| 2” Bolts (26) and Base Washers (130) into the base of the |
| 23 | 26 |
| 51 |
| Uprights and the |
|
| |||
| Bolts (23) and two |
| 65 |
|
|
|
| treadmill forward if necessary. Tighten the two 2” Bolts. |
|
|
|
| |
|
|
| 130 |
|
| |
|
|
|
|
|
| |
5. | Make sure that all parts are properly tightened before | 98 | 20 |
|
|
|
| you use the treadmill. Place a mat beneath the tread- |
|
|
|
| |
|
| 98 |
|
|
| |
| mill to protect the floor. For your benefit, familiarize |
|
| 23 |
| |
| yourself with the information on pages 23 and 24. |
|
|
|
| |
|
|
|
|
|
| |
If you purchase the optional chest pulse sensor (see page | 1 |
|
|
|
| |
20), follow the steps below to install the receiver and the |
|
|
|
| ||
|
|
|
|
| ||
short jumper wire included with the chest pulse sensor. |
|
|
|
|
| |
1. Make sure that the power cord is unplugged. Remove the |
|
|
|
|
| |
| indicated 3/4” Screws (40) from the Console Back (117). |
|
|
|
|
|
| Remove the Console Back. |
|
|
|
|
|
|
|
| 117 |
|
| |
|
|
| 40 | 40 |
|
|
2. Connect the Short Jumper Wire (A) to the wire on the | 2 |
|
|
|
| |
| Receiver (B). Connect the other end of the Short Jumper |
|
|
|
| |
|
|
|
|
|
| |
| Wire to the PULSE jack on the back of the Console (80). |
|
|
|
|
|
| Turn the Receiver (B) so the cylinder is on the side |
| 80 |
|
|
|
| shown, and hold the Receiver against the back of the |
|
|
|
| |
|
| A |
| Cylinder |
| |
| Console (80). Attach the Receiver with the two Small |
|
|
| ||
| Screws (C) included with the receiver. |
|
|
| B |
|
|
|
| C |
|
|
|
Make sure that no wires are pinched. See step 1.
Reattach the Console Back (117) with the 3/4” Screws (40).
You may discard the other wires included with the receiver.
7
