Installing the Insert (continued) | Installation (suite) |
Step 9
Before Lighting the Appliance
Before lighting the appliance, do the following:
Review safety warnings and cautions
•Read the Safety and Warning Information section at the beginning of this Installers Guide.
•Before lighting the appliance,
•Before lighting the appliance,
•Any component that is found to be faulty MUST BE replaced with an approved component. Tampering with the appliance components is DANGEROUS and voids all warranties.
A small amount of air will be in the gas supply lines. When first lighting the appliance, it will take a few minutes for the lines to purge themselves of this air. Once the purging is complete, the appliance will light and will operate normally.
Subsequent lightings of the appliance will not require this purging of air from the gas supply lines, unless the gas valve has been turned to the OFF position, in which case the air would have to be purged.
NOTE: The fireplace should be run for 8 hours on the initial
Step 10
Lighting the Appliance
You’ve reviewed all safety warnings, you’ve checked the appliance for gas leaks, you know the vent system is unobstructed, and you’ve checked for faulty components. Now you’re ready to light the appliance.
WARNING: PLEASE REFER TO THE USER’S ! MANUAL FOR ALL CAUTIONS, SAFETY AND WARNING INFORMATION PERTAINING TO THE LIGHTING AND OPERATION OF THE APPLI-
ANCE.
After the Installation
LEAVE THIS INSTALLATION MANUAL WITH THE APPLIANCE FOR FUTURE REFERENCE.
Étape 9
Avant l’allumage
Avant d’allumer l’appareil de chauffage au gaz, ne pas oublier de:
Relire et assimiler les consignes de sécurité
•Relire la section Consignes de sécurité au début de ce Guide d’installation.
Vérifier qu’il n’y a pas de fuites de gaz.
•Avant d’allumer l’appareil de chauffage, s’assurer qu’il n’y a pas de fuites de gaz.
Vérifier qu’il n’y a pas d’obstructions au niveau de la mitre et des grilles frontales.
•Avant d’allumer l’appareil de chauffage, s’assurer qu’il n’y a pas d’obstructions dans le système de ventilation au niveau de la mitre et des grilles frontales.
Vérifier qu’il n’y a pas d’éléments défectueux.
•Tout pièce défectueux DOIT ÊTRE remplacée par une pièce homologuée. Toute modification des éléments de l’appareil de chauffage est DANGEREUSE et annule toutes les garanties.
La conduite d’alimentation en gaz contient une petite quantité d’air. Lors du premier allumage, attendre quelques minutes pour que la tuyauterie se purge
Par la suite, il est inutile de purger la tuyauterie à chaque allumage, à moins que la vanne de commande n’ait été FERMÉE. Dans ce
REMARQUE : Vous devez faire fonctionner le foyer pendant 8 heures la première fois que vous l’allumez. Cela permet de mieux éliminer les produits chimiques utilisés dans la peinture et les bûches.
Étape 10 Allumage
Une fois les consignes de sécurité revues, l’absence de fuites de gaz vérifiée, l’absence d’obstruction dans le système de ventilation confirmée, les éléments inspectés, l’appareil de chauffage au gaz peut être allumée.
ATTENTION: VOIR LE GUIDE D’INSTALLATION ! POUR LES CONSIGNES DE SÉCURITÉ ET LES AVERTISSEMENTS RELATIFS À L’ALLUMAGE
ET AU FONCTIONNEMENT DE L’APPAREIL.
Après l’installation
LAISSER CE GUIDE D’INSTALLATION À PROXIMITÉ DE L’APPAREIL POUR POUVOIR LE CONSULTER EN CAS DE BESOIN.
26