Getting Started | Heat & Glo LifeStyle BE-41IPIC, BE-41C, BE-41LPC

4	Getting Started	Installer Guide

A. Typical Appliance System

NOTICE: Illustrations and photos reﬂect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

Note: Dual venting configurations ARE NOT allowed. Appliance MUST be vented EITHER vertically OR horizontally.

NON-COMBUSTIBLE ROOF FLASHING

MAINTAINS MINIMUM CLEARANCE

AROUND PIPE (SECTION 10.G)

VENT PIPE (SECTIONS 7 and 8)

CEILING FIRESTOP ON FLOOR OF ATTIC (SECTION 8.C)

VERTICAL TERMINATION CAP (SECTION 10.J)

STORM COLLAR (SECTION 10.H)

VENT PIPE PENETRATES ROOF PREFERABLY WITHOUT AFFECTING ROOF RAFTERS (SECTION 8.C)

ATTIC INSULATION SHIELD (NOT SHOWN) MUST BE USED HERE TO KEEP INSULATION AWAY FROM VENT PIPE IF ATTIC IS INSULATED (SECTION 8.D)

HORIZONTAL

TERMINATION CAP (SECTION 10.M )

FRAMING/HEADER (SECTION 5.B)

FRAMING HEADED OFF IN CEILING JOISTS (SECTION 8.C)

OPTIONAL

WALL SWITCH

MANTEL AND MANTEL LEG (SECTION 5.D)

SURROUND

HEARTH EXTENSION

GAS LINE (SECTION 11)

Figure 4.1 Typical System

Heat & Glo • BE-41C / LP, BE-41IPIC / LP • 2105-900 Rev. P • 6/09

17

Image 17

Heat & Glo LifeStyle BE-41IPIC, BE-41C, BE-41LPC, BE-41IPILPC owner manual Getting Started, Typical Appliance System

Contents

Hot glass will cause burns What to do if you smell gas Homeowner Reference Information Congratulations User Guide Table of Contents Troubleshooting Appliance SetupFinishing Reference Materials Limited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit optional Clear Space On position. The ON/OFF switch may Turn off all electric power to the applianceLighting Instructions IPI Final inspection by Lighting Instructions Standing Pilot For Your Safety Read Before Lighting Lighting Instructions After Fireplace is Lit Frequently Asked Questions Maintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote Control Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualiﬁed Service TechnicianVenting Logs Either cobrahead or SIT Typical Appliance System Getting Started Tools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Any such action may cause a ﬁre hazard Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase Combustible Mantel Legs or Wall Projections Mantel and Wall ProjectionsCombustible Mantels Vent Termination Minimum Clearances Termination Locations Covered Alcove Applications Approved Pipe Vent Information and DiagramsVent Table Key Use of Elbows One Elbow Vent Diagrams Top Vent Horizontal TerminationTwo Elbows V1 Minimum H1 Maximum Min Max Top Vent Horizontal Termination Three Elbows Break Here Maximum + V 2 Min Top Vent Vertical Termination H1 + H2 V1 + V2 Minimum H1 + H2 Maximum Top Vent Vertical Termination Three Elbows Heat & Glo BE-41C / LP, BE-41IPIC / LP 2105-900 Rev. P 6/09 H1 Maximum V1 Minimum H2+ H3 H1+ H2+ H3 Max Rear Vent Horizontal Termination Two ElbowsH1 Maximum V1 Minimum H1 + H2 Maximum H1 + H2 Maximum V1 Minimum Rear Vent Vertical Termination One Elbow V1 Minimum H1 + H2 + H3 Rear Vent Vertical Termination Three Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall Penetration Pipe DVP SLP Install the Ceiling Firestop Vaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Top Vent Appliance Preparation Cut the metal retaining band and fold the sides out Rear Vent Securing and Leveling the Appliance Installing the Non-combustible Board Attach Vent to the Firebox Assembly Installing Vent Pipe DVP and SLP PipeAssemble Vent Sections DVP Pipe Only Assemble Pipe Sections Assemble Slip Sections Assemble Vent Sections SLP Pipe Only Disassemble Vent Sections Secure the Vent Sections Install Decorative Ceiling Components SLP only Assemble and Install Storm Collar Install Metal Roof Flashing Heat Shield Requirements for Horizontal Termination Install Vertical Termination CapInstall Decorative Wall Components SLP only Refer to of this manual Install Horizontal Termination Cap DVP and SLP PipeAnsi Z223.1 and CAN/CGA-B149 installation codes Fuel Conversion Gas InformationGas Pressure Gas Connection IntelliFire Ignition System Wiring Wiring RequirementsStanding Pilot Ignition System Wiring Optional Accessories Requirements IntelliFire Pilot Ignition IPI Wiring Diagram Electrical Service and Repair Wall Switch Installation for Fan Optional Junction Box Installation Facing Material Finishing Finish Door FIT Material See Maximum Thickness Doors Appliance Setup Install the Log Assembly LOG Assembly LOGS-6000BE Log Placement Tabs Air Shutter Setting Install Trim and/or SurroundAir Shutter Settings Burner Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action Troubleshooting IntelliFire Ignition System Ues to spark, and main Location Inches Millimeters Appliance Dimension DiagramReference Materials DVP vent components Vent Components Diagrams DVP vent components Horizontal Termination Cap Roof Flashing Multi-pak 13-3/4 11-7/8 349 mm 787 mm 13-1/4 367 mm 24-5/8 625 mm 27-1/2 127 mm302 mm 13-3/4 13-7/8 352 mm 349 mm DVP-TVHW DVP-HRC-SS DVP-HRC-ZC-SS Horizontal Termination CAP Elbow Effective Height Length 165 mm 222 mm 168 mmHorizontal Pipe Support 2 in mm 152 mm 8 in mm 251 mm SLP-90ST 90 Elbow Snorkel Cathedral CeilingSupport Box-Black Termination Cap Ceiling Firestop Contact Information