Framing and Clearances | Heat & Glo LifeStyle BE-41IPILPC, BE-41C

5 Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be locat- ed out of trafﬁc and away from furniture and draperies.

NOTICE: Illustrations reﬂect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

G

1/2 IN.

A

D

H

A

B C

TOP VENT

ONE 90º ELBOW

REAR VENT,

HORIZONTAL TERMINATION,

TWO ELBOWS

B

D

B

ALCOVE

INSTALLATION E

		REAR VENT,
	REAR VENT,	ONE ELBOW
	REAR VENT,	B
	NO ELBOWS	B	D
	NO ELBOWS
	B

F

D

	A	B	C	D	E	F	G	H
Inches	51	42	72	56-5/8	See Section D.	22	17-3/4	8
Millimeters	1295	1067	1829	1438	Mantel Projections	559	451	203

Figure 5.1 Appliance Locations

Heat & Glo • BE-41C / LP, BE-41IPIC / LP • 2105-900 Rev. P • 6/09

19

Image 19

Heat & Glo LifeStyle BE-41IPILPC, BE-41C, BE-41IPIC, BE-41LPC Framing and Clearances, Selecting Appliance Location

Contents

Hot glass will cause burns What to do if you smell gas Homeowner Reference Information Congratulations User Guide Table of Contents Reference Materials Appliance SetupTroubleshooting Finishing Limited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optional Final inspection by Turn off all electric power to the applianceOn position. The ON/OFF switch may Lighting Instructions IPI Lighting Instructions Standing Pilot For Your Safety Read Before Lighting Lighting Instructions After Fireplace is Lit Frequently Asked Questions Remote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass Cleaning Logs Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection Venting Either cobrahead or SIT Typical Appliance System Getting Started Any such action may cause a ﬁre hazard Design and Installation ConsiderationsTools and Supplies Needed Inspect Appliance and Components Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase Combustible Mantels Mantel and Wall ProjectionsCombustible Mantel Legs or Wall Projections Vent Termination Minimum Clearances Termination Locations Covered Alcove Applications Use of Elbows Vent Information and DiagramsApproved Pipe Vent Table Key V1 Minimum H1 Maximum Vent Diagrams Top Vent Horizontal TerminationOne Elbow Two Elbows Min Max Top Vent Horizontal Termination Three Elbows Break Here Maximum + V 2 Min Top Vent Vertical Termination H1 + H2 V1 + V2 Minimum H1 + H2 Maximum Top Vent Vertical Termination Three Elbows Heat & Glo BE-41C / LP, BE-41IPIC / LP 2105-900 Rev. P 6/09 H1 Maximum V1 Minimum H1 + H2 Maximum Rear Vent Horizontal Termination Two ElbowsH1 Maximum V1 Minimum H2+ H3 H1+ H2+ H3 Max H1 + H2 Maximum V1 Minimum Rear Vent Vertical Termination One Elbow V1 Minimum H1 + H2 + H3 Rear Vent Vertical Termination Three Elbows Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Pipe DVP SLP Install the Ceiling Firestop Flat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Top Vent Appliance Preparation Cut the metal retaining band and fold the sides out Rear Vent Securing and Leveling the Appliance Installing the Non-combustible Board Assemble Pipe Sections Installing Vent Pipe DVP and SLP PipeAttach Vent to the Firebox Assembly Assemble Vent Sections DVP Pipe Only Assemble Slip Sections Assemble Vent Sections SLP Pipe Only Disassemble Vent Sections Secure the Vent Sections Install Decorative Ceiling Components SLP only Assemble and Install Storm Collar Install Metal Roof Flashing Install Decorative Wall Components SLP only Install Vertical Termination CapHeat Shield Requirements for Horizontal Termination Ansi Z223.1 and CAN/CGA-B149 installation codes Install Horizontal Termination Cap DVP and SLP PipeRefer to of this manual Gas Connection Gas InformationFuel Conversion Gas Pressure Optional Accessories Requirements Wiring RequirementsIntelliFire Ignition System Wiring Standing Pilot Ignition System Wiring IntelliFire Pilot Ignition IPI Wiring Diagram Electrical Service and Repair Wall Switch Installation for Fan Optional Junction Box Installation Facing Material Finishing Finish Door FIT Material See Maximum Thickness Doors Appliance Setup Install the Log Assembly LOG Assembly LOGS-6000BE Log Placement Tabs Burner Install Trim and/or SurroundAir Shutter Setting Air Shutter Settings Symptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Symptom Possible Cause Corrective Action Troubleshooting IntelliFire Ignition System Ues to spark, and main Reference Materials Appliance Dimension DiagramLocation Inches Millimeters DVP vent components Vent Components Diagrams DVP vent components Horizontal Termination Cap 13-3/4 13-7/8 352 mm 349 mm 787 mm 13-1/4 367 mm 24-5/8 625 mm 27-1/2 127 mmRoof Flashing Multi-pak 13-3/4 11-7/8 349 mm 302 mm DVP-TVHW DVP-HRC-SS DVP-HRC-ZC-SS Horizontal Termination CAP 2 in mm 152 mm 8 in mm 251 mm SLP-90ST 90 Elbow 165 mm 222 mm 168 mmElbow Effective Height Length Horizontal Pipe Support Ceiling Firestop Cathedral CeilingSnorkel Support Box-Black Termination Cap Contact Information